KoolMore CIM-315 Скачать руководство пользователя страница 12

Страница: 12 / 12

touble

reason

solution

“

” appear

Insufficient water

Low

water

inputting

pressure

pipe

blockage

—add pressure or clean the pipe

The ball on Level switch

locked

Cleaning the water tank and level switch

Water isn

’

t remaining in

the unit

Place the machine in horizontal position

Water leaves the drain

Put the drain plug and do adjustment

Pump working but

no water flow out

through the

distributive pipe

Pipe blockage

Clean the hole

Bad ice

transparency

Water is not good

Change water, filter and soften the incoming

water

Ice irregular

Poor water quality or dirty

water tank

Clean the water tank and change the water

Hole on distributive pipe

blocked

Clean distributive pipe

Ice is too thin

High ambient

temperature

Move the machine to a cool place or add ice

making time

unventilated

Keep the surrounding of machine more than

8 Inches

Ice is too thick

Lower the ambient

temperature

Reduce the ice making time

“ICE FULL” showed

Ice is full

Move the ice out of the tank

Ice blocks the detecting

board

Wait for the ice to melt

Ice making process

is normal but no ice

High ambient

temperature or high

water temperature

Move the machine to a place lower than 32

℃

add cool water

Refrigerant leak

Call an authorized technician

Refrigeration blocked

Call an authorized technician

Troubleshooting display

A. Ambient temperature sensor is broken:

E1.

B. No ice or refrigerant leak: E2.

C. Magnetic valve disconnected, the indicator of ice full displayed. After connecting, the indicator

darken

D. Press ON/OFF for more than 5s, and the machine start to de-icing. After it finished, the

process of ice making proceeds.

TOUBLESHOOTING

Содержание CIM-315













Результаты поиска

Содержание CIM-315

Отзывы:

Похожие инструкции для CIM-315

Бренды по названию

Популярные бренды

KoolMore CIM-315, Инструкция по эксплуатации

Результаты поиска

Содержание CIM-315

Отзывы:

Похожие инструкции для CIM-315

Бренды по названию

Популярные бренды