manualshive.com logo in svg

Kontron AT8902M, Руководство пользователя

Поделиться
Скачать
Kontron AT8902M Скачать руководство пользователя страница 67

AT8902M

Software Description

Page 4 - 2

AT8902M User Guide

4.

Software Description

Software on the AT8902M includes the following parts:

• Bootloader

• OS (rootFS, kernel)

• Application SW

• IPMI  FW

The Software accomplishes operation of the switching hardware and is therefore also refer-
enced as firmware. It is preinstalled on the system and can only be updated by a dedicated
update procedure. This manual only describes bootloader, its self tests and IMPI Firmware and
introduces the update procedure. 

For additional information of system configuration using CLI commands refer to documentation
“

AT8901/02/04M CLI Reference Manua

l”.

4.1

Supported RFCs

The Software supports the following standards and RFCs.

4.1.1

Management 

• RFC 826 - ARP

• RFC 854 - Telnet

• RFC 855 - Telnet Option

• RFC 1155 - SMI v1

• RFC 1157 - SNMP

• RFC 1212 - Concise MIB Definitions

• RFC 1867 - HTML/2.0 Forms w/ file upload extensions

• RFC 1901 - Community based SNMP v2

• RFC 2068 - HTTP/1.1 protocol as updated by draft-ietf-http-v11-spec-rev-03

• RFC 2246 - The TLS Protocol, Version 1.0

• RFC 2271 - SNMP Framework MIB

• RFC 2295 - Transparent Content Negotiation

• RFC 2296 - Remote Variant Selection; RSVA/1.0 State Management "cookies" 

• RFC 2346 - AES Ciphersuites for Transport Layer Security

Содержание AT8902M





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды