manualshive.com logo in svg

Kontron AT8902M, Руководство пользователя

Поделиться
Скачать
Kontron AT8902M Скачать руководство пользователя страница 3

AT8902M

Preface

Page iii

AT8902M User Guide

Table of Content

Revision History  .........................................................................................................ii
Imprint ........................................................................................................................ii
Disclaimer ..................................................................................................................ii
Proprietary Note ........................................................................................................ix
Trademarks ...............................................................................................................ix
Environmental Protection Statement .........................................................................ix
Explanation of Symbols  .............................................................................................x
For Your Safety  ..........................................................................................................x

High Voltage Safety Instructions ...........................................................................xi
Special Handling and Unpacking Instructions ......................................................xi
General Instructions on Usage  ............................................................................ xii

Two Year Warranty .................................................................................................. xiii

Chapter

1

1.

Introduction .................................................................................................. 1 - 2

1.1 Product Overview .................................................................................... 1 - 2

1.1.1

AT8902M Features  ......................................................................... 1 - 3

1.1.2

General compliances  ...................................................................... 1 - 4

1.1.3

Optional Accessories ...................................................................... 1 - 4

1.1.4

Hot Swap Capability  ....................................................................... 1 - 4

1.1.5

Board Options ................................................................................. 1 - 5

1.2 Technical Specification  ........................................................................... 1 - 6
1.3 Software Support ................................................................................... 1 - 12

Chapter

2

2.

Installation ................................................................................................... 2 - 2

2.1 Safety Requirements ............................................................................... 2 - 2
2.2 AT8902M Initial Installation Procedures .................................................. 2 - 3
2.3 Standard Removal Procedures  ............................................................... 2 - 4
2.4 AMC Installation  ...................................................................................... 2 - 4
2.5 Software Installation  ................................................................................ 2 - 4
2.6 CLI Quick Start  ........................................................................................ 2 - 4

Содержание AT8902M





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды