Kontron AM4100 Скачать руководство пользователя | Manualshive

Страница: 98 / 150

background image

NetBootLoader

AM4100

Page 5 - 10

ID 36126, Rev. 2.0

P R E L I M I N A R Y

5.4.3.2

CBL

This command is used to set or display the bootline associated with a particular kernel image
or which is common to all images.

5.4.3.3

DHCP

This command is used to obtain automatically networking parameters from either a DHCP or
BOOTP server for an Ethernet port. Its use requires the availability of one or the other of these
servers to function.

5.4.3.4

FDT

This command is used to disable or enable the creation of a flattened device tree.

The flattened device tree provides information required by certain operating systems for oper-
ation of system devices.

5.4.3.5

NET

This command is used to set or display the parameters for the configuration of the specified
Ethernet port of the AM4100. The Ethernet interfaces are only available after these settings
have been made.

5.4.3.6

PASSWD

This command is used to set the password used by the NetBootLoader for the operation of the
telnet interface. No password is required for access from the SER0 interface.

5.4.3.7

PF

This command is used to set the port parameters for the SER0 and SER1 serial interfaces only
for the current operator session. The next system restart will cause these settings to revert to
the default settings of: 9600 Baud, 8 bits per character, 1 stop bit, and no parity. This is done
to preclude a system lockout when restarting due to incompatible settings.

5.4.3.8

SCRIPT

This command permits the automatic invoking of NetBootLoader commands during boot up.
The operator issues this command with appropriate options and then restarts the system. Dur-
ing the boot operation at boot wait time expiration, the script commands will be executed.

Use of this command permits, for example, remote booting from an TFTP server.

«
...
96
97
98
99
100
...
»

Содержание AM4100























































































































































Отзывы:

Нет отзывов

Похожие инструкции для AM4100

Бренд: Dantherm Страницы: 96

Бренд: easydriver Страницы: 26

Бренд: Calsense Страницы: 10

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Jabra Страницы: 4

Бренд: Watts Страницы: 4

Бренд: WaterCop Страницы: 4

Бренд: B&G Страницы: 19

Бренд: National Instruments Страницы: 78

TBEN-L 8IOL Series

Бренд: turck Страницы: 148

APEXpy 07-37A2-2111/ 520Series

Бренд: Bartec Страницы: 98

Бренд: Gecko Страницы: 82

Бренд: Harman Страницы: 2

Бренд: Linear Technology Страницы: 6

Бренд: Nortek Страницы: 24

Бренд: Belimo Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды