Könner & Söhnen KS 48V-DC Скачать руководство пользователя страница 5

OVERLOAD INDICATOR

OVERLOAD INDICATOR

The overload indicator lights up when the connected generator is overloaded, the inverter control unit 

overheats or the output voltage rises.
In this case, you must perform the following steps:
1. Turn off all connected electrical appliances and stop the engine.
2. Reduce the total power of the connected devices until the nominal power of the generator is reached.
3. Check if the vent grid is clogged. Remove excess dirt or debris, if any.
4. After checking, start the engine.

The overload indicator may light up within several sec-

onds after start-up. However, this is not a malfunction.

IMPORTANT!

CHECKING THE FUEL LEVEL

CHECKING THE FUEL LEVEL
1. Unscrew the fuel cap and check the fuel level in the tank.
2. Fill the fuel tank to the fuel filter level.
3. Tighten the fuel cap securely.
Recommended fuel: 

Recommended fuel: unleaded fuel.
Fuel tank volume:

Fuel tank volume: see specifications table.

CHECK BEFORE GETTING STARTED

5

Wipe up spilled fuel immediately with a clean, dry, soft 

cloth, as the fuel may harm painted surfaces or plastic 

parts.

IMPORTANT!

CHECKING THE OIL LEVEL

CHECKING THE OIL LEVEL
The generator is transported free of motor oil. Do not start the engine until it is filled with sufficient amount 

of motor oil.
1. Unscrew the oil dipstick and wipe it out with a clean cloth.
2. Insert the dipstick without screwing it in.
3. Check the oil level by a mark on the oil dipstick.
4. Add oil if its level is below the mark on the oil dipstick.
5. Screw on the dipstick.

Recommended motor oil: 

Recommended motor oil: SAE 10W-30, SAE 10W-40.

Motor oil quantity: 

Motor oil quantity: 

see specifications table.

FILL TO HERE

FILL TO HERE

Use only unleaded gasoline. Using leaded gasoline can 

cause serious damage to the inside of the engine.

IMPORTANT!

GETTING STARTED

6

Do not change the controller settings in terms of the 

amount of fuel or speed governor (this adjustment 

was made at the factory). Otherwise, this may result in 

changes in the engine operation or its failure.

IMPORTANT!

konner-sohnen.com

   

|

    4

Содержание KS 48V-DC













Отзывы: