44060 Adapter for Product Holder
- Extraordinarily practical and versatile
- With the help of this adapter you can use almost all *Products Support Arms on the SPACEWALL from the extensive K&M program.
-
This system is very easy to use (Article 44110 - 44380, *not compatible: 44140, 44185/186) on a regular wall.
- Once installed this product makes it easy to attach, change, switch or remove different Product Support Arms in seconds.
-
The Product Support Arm is easy to use and attach - tools are not required.
- If desired, an additional screw provides increased stability.
-
For example: to make it more difficult for unauthorized individuals to remove it.
- If the Product Support Arm is not needed, all that is left on the wall is the flat and inconspicuous housing - until it is needed again.
SAFETY NOTES
WALL MOUNT
ATTACH THE PRODUCT SUPPORT ARM
- Routinely check the stability of the screws and fit.
- Also routinely check to ensure the mounting plate is secure in the holder.
- To care for the product use a damp cloth and a non-abrasive cleaning agent.
FAULT FINDING (F) and SOLUTION (S)
F: Product Support Arm cannot be placed (hung) properly
F:
B: Please note: Models 44140, 44185/86 are not suitable
F: Product Support Arm can be lifted up
F:
B: Place (hang) the mounting plate correctly: see instruction steps (4-7)
F:
B: If needed, secure this by screwing in the tapping screw (8,9)
LEVEL THE ADAPTER
1. Make sure the mounting plate is vertical,
1.
mark the drill holes.
Adapter 44060
Product Support Arm (Example: 44210, for Violins)
continues on
the back:
STEP
BY
STEP:
Place (hang)
the Product
Support Arm
into the
Adapter and
secure it
2. Drill three holes:
2.
- ø 6 mm for the corresponding
2.
a. Plastic anchor
2. a.
(Concrete, stone)
2.
b. Frame anchor
2. b.
(Perforated bricks)
2.
- A pilot hole does not have
2. -
to be drilled for so-called
2.
c. Particle board screws
2. c.
(Wood wall)
CHECK, MAINTENANCE, CLEANING
TECHNICAL DATA
Material
Adapter: Polyamid, fiber glass reinforced, black
Tapping screw: Steel, powder coated, black
max. Load
K&M Product Support Arm Model Series 44110 - 44380
Excepted: Article No. Art.-No. 44140, 44185, 44186
Dimensions
W x D x H: 85 x 18 x 101 mm; 0.05 kg
Packaging
PE-Bag 125 x 200 mm
- Please comply with the local installation instructions (they may differ from the INSTALLATION EXAMPLES (see below))
- Only mount on suitable walls with the corresponding assembly material (not included in the delivery)
- Walls that are too weak or have electrical and water conduits are not suitable.
- In case of doubt consult a qualified technician.
- Check the stability of the installation regularly.
- Careful and attentive handling is required: A. When hanging up the product support arm adapter be sure not to pinch your fingers.
- Careful and attentive handling is required:
B. Be sure to follow the correct order when installing the adapter: first the top and then the bottom.
Thank you for choosing this product. The instructions provide directions to all of the important set up and handling steps. We
recommend you keep these instructions for future reference.
MOUNT EXAMPLES
3.a. Concrete, Stone - Example: Plastic Anchor ø 6 x 36
3.b. Perforated bricks - Example: Frame Anchor 6 x 60
drill, blow out the drill hole, hammer in the anchor,
drill and counter sink, blow out the drill hole, set the anchor,
install the mounting plate, screw in the screws
install the mounting plate, screw in the screws
Fig.:
Stein-
Bohrer
3.c. Wood beams - Example: Particle Board Screw: ø 4.5 x 40 without a pilot hole, install the mounting plate, screw in
3.c.
the screws
