1. PACKAGING AND PARTS OVERVIEW
- A suitable, i.e. load bearing and level surface is required.
- Protect the stand from wind, being bumped into by the audience etc..., otherwise there is a high risk that it could fall over.
- Ensure that the screws are tight and check this periodically.
- The position of the extension arm is secured with a locking pin/bolt - this must always be set properly
-
(please refer to Section 4). The screen/monitor stand comes with the “locking pin/bolt” pre-assembled and allows the
-
user to setup the screen/monitor stand without the use of any tools. Alternatively a SECURITIY SCREW is also
-
provided, which requires the use of a screw driver (please refer to the separate instructions).
-
PLEASE NOTE: this is recommended in the event of possible incorrect use (at a public event, around
-
children).
- Cables that are inside the tubes are to be protected against abrasion (for example protective tubing), specifically where
-
the cables come out of the tubes; ask an expert (see Section 8).
- The stand is equipped with plastic end caps to protect the floor. A slip resistant pad should be used, if needed.
- When setting up the stand or adjusting the stand - please use two people (one person to hold the extension arm, the second person
-
operates the locking pin/bolt).
2. SETUP STAND
SAFETY NOTES
SET UP INSTRUCTIONS
Thank you for choosing this product. The instructions provide directions to all of the important set up and handling
steps. We recommend you keep these instructions for future reference.
26783 Screen/Monitor Stand
High level of stability and the screen/monitor is easy to attach.
The assembly accessories provided with the product allow one to assemble according to the VESA Standard for 42" to 65"
flat screens. The large tubing saves space by providing a place to organize and store cables.
Weight: 15.5 kg; variable height adjustment from 1100 - 1650 mm (Screen/Monitor Center).
Locking pin/bolt
is only to be
used when the
tube/arm is
extended.
a. Screw the Counter Nuts
7
on the
a.
thread of the positioning plate
8
...
b. Screw in the thread of the posi-
b.
tioning plate
8
in the connec-
b.
tor of both base tubes
2
.
c. Approximately at the same height
X
c.
of the plate - be sure there is a bit of space
c.
between the counter nuts and the tube.
d. Position the positioning plate by
d.
tightening the counter nuts.
d.
Key SW13
19
.
e. Screw the base tubes
2
to the base
e.
vertical tubes
4
(please refer to (Step 1, 2 and 3).
e.
Tip: Please pay attention to the position of the holes.
g. Carefully place the
g.
base with the tube
g.
combination onto
g.
the floor
f. Connect the stand tube combination with the base:
f.
- place base tube
1
from above into the base vertical tube
4
f.
- hold counter plate
6
from below to the vertical tube
4
f.
- and screw together using two raised counter sunk-head screws M8 x 60 mm
9
f.
- with key SW5
17
f.
- Torque 20 Nm
1. Screw in the screws
10
and tighten loosely with
1.
Key SW5
17
, if needed loosen a quarter turn
2. Screw in screws
10
2.
and tighten
2.
- Torque 8 Nm
3. Tighten screws - torque 8 Nm
2.a Adjustable
Base
2.b B a s e
Box 1: 1210 x 270 x 125 mm
26783 Monitor Stand
INSTRUCTIONS
1 - Stand tube combination
2 - Base tube right & left
3 - Mounting strips
4 - Base-vertical tubes
5 - Screen/Monitor vertical
5 -
tubes (2x)
5a- Cylinder screws (4x)
6 - Counter-plate
*6.b Vertical tubes
*6.b
to stand
*6.d Screen to
*6.d
stand
*6.a Mounting
*6.a
strips to
*6.a
screen
*6.a Mounting
*6.a
strips to
*6.a
screen
alternativ:
Screen sets for
screen/monitor
attachements:
Alternative!
Safety
Screw
*2.a Adjustable Base
Step 2
Step 2
Step 5 + 6
Step 5 + 6
Step 5 + 6
6-26783-5-00
6-26783-6-00
6-26783-3-00
*Please refer to associated sections in the following instruction manual
*2.b Base
washers are
placed for the
finale adjustment
of the cylinder
screws
5a
Please refer to
side 3, Fig.:
down right
Z 3:1
