manualshive.com logo in svg

Konica Minolta IP-011, Руководство по обслуживанию

Поделиться
Скачать
Konica Minolta IP-011 Скачать руководство пользователя страница 26

4-1  IP-011 PRINTER CONTROLLER

Chapter 4  Appendices

■

 Rewriting the firmware

The IP-011 is equipped with flash ROM and the firmware can be upgraded via the parallel port.

●

 Preparation

•

Connect the IP-011 through a parallel cable to the computer that is used to upgrade the

firmware.

•

Prepare the replacing firmware in the hard disk of the computer or in the form of CD-ROM.

•

Turn on the copier’s main and auxiliary powers.

●

 Procedure of rewriting the firmware

1. On the monitor screen of the computer, click the Start button. Click and select [MS-DOS

Prompt] from [Program].

The [MS-DOS prompt] appears.

2. Responding to the [MS-DOS prompt], designate the folder where the firmware is held.

Execute a COPY command and press the Enter key.

<Example> C:\copy filename.xxx lpt1 /b

3. On completion of file transfer from the computer, a message indicating the completion of

transfer appears on the copier LCD control panel. Press the OK button.

Now rewriting the firmware starts.

Содержание IP-011




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды