Kongsberg cJoy OT Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 208

background image

Kongsberg cJoy OT

Upgrading the operator terminal software

The application software stored in the flash PROM of the controller PS (RCU) in the
joystick controller cabinet can be copied to the hard disk of the operator terminal
provided that the system is in

Standby

mode.

If the operator terminal has been replaced, it is very unlikely that the application software
installed on the replacement operator terminal will be exactly the same as that stored in
the flash PROM of the controller PS. This will normally be indicated by the

File version

match

field on the Software Upgrade and Restart input dialog (see

Software Upgrade

and Restart input dialog

on page 59) which will be red.

In this situation the application software stored on the hard disk of the operator terminal
will need to be upgraded with the application software stored in the flash PROM of
the controller PS.

Caution

The following procedure should only be performed if the colour of the

File

version match

field on the Software Upgrade and Restart input dialog is red,

and then preferably by a Kongsberg Maritime software engineer.

To upgrade the operator terminal application software from the flash PROM of the
controller PS, proceed as follows:

1

Display the Software Upgrade and Restart input dialog.

2

Ensure that the colour of the

File version match

field is red.

3

Move the focus to the

Upgrade from Remote Control Unit

field and change the

option to

Yes

.

4

Press the

Enter

button.

• The operator pop-up message

Please be patient... This will take some time.

is

displayed.

• Copying of the application software stored in the flash PROM of the controller

PS over to the hard disk of the operator terminal is started.

• The

Status

field for the

Upgrade from Remote Control Unit

function changes to

yellow and all option fields become unavailable.

• When the software upgrade has been completed, the

Status

field for the

Upgrade

from Remote Control Unit

function changes to green and all option fields become

available with the

Upgrade from Remote Control Unit

field in focus (selected).

5

Restart the operator terminal (see

Restarting the operator terminal

on page 81

for procedure details).

Upgrading the controller PS software

The application software stored on the hard disk of the operator terminal can be copied
to the flash PROM of the controller PS (RCU) in the joystick controller cabinet provided
that the system is in

Standby

mode.

82

385585/C

«
...
80
81
82
83
84
...
»

Содержание cJoy OT

















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для cJoy OT

Бренд: Valor Страницы: 20

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 2

GA Industries 930-DT

Бренд: Vag Страницы: 4

Бренд: M-system Страницы: 13

Бренд: MARTINS Industries Страницы: 20

WisLink LPWAN RAK5146

Бренд: RAKwireless Страницы: 9

CURTIS DC Series

Бренд: NOCO Genius Страницы: 2

Бренд: TimeTec Security Страницы: 2

Бренд: Xylem Страницы: 2

Бренд: Tamiya Страницы: 5

EAGLE GRIP EG4MDC2-F

Бренд: Easy Lift Equipment Страницы: 17

Бренд: K+R Performance Engineering Страницы: 12

RSF B mini Series

Бренд: Harmonic Drive Страницы: 33

Бренд: ENTRYPASS Страницы: 42

Бренд: ApexWaves Страницы: 16

ConnectCore 6 Plus

Бренд: Digi Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды