background image

COMPLIANCE

WARNING: SHOCK HAZARD - DO NOT OPEN 

DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE

ATTENTION: RISQUE DE CHOC ÉLÉCTRIQUE - NE PAS OUVRIR

TENIR A L’ABRIS DE LA PLUIE ET DE L’HUMIDITÉ

CAUTION

CAUTION: To prevent the risk of electric shock, do not remove cover (or back plate). There are no user serviceable parts 

inside. Refer servicing to qualified service personnel.

This appliance may not be treated as regular household waste. Management of WEEE (Waste Electrical and Electronic 

Equipment) is applicable in member states of the European Union and other European countries with individual national 

policies on the management of WEEE. If you need more information on the collection, reuse and recycling systems,

please contact your local or regional waste administration facility.

The product complies with the following European directives: 2015/35/EU (CE-LVD)

2015/30/EU (CE-EMC)

2014/53/EU (RED)

,

2011/65/EU

2015/863(ROHS)

.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause 

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired 

operation.

FCC warning:

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to oper-

ate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC 

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-

ment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may 

cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the 

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an 

uncontrolled environment. This equipment should be installed and operated with 

minimum distance 20cm between the radiator & your body.

IC warning

- English:

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any

interference, including interference that may cause undesired operation of the device.

- French:

Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.

L'exploitationestautorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le

fonctionnement.

Содержание K-multi6









Отзывы: