Kone V3F18, Инструкция по установке

Страница: 37 / 42

V3F25/18 drive V3F25/18 drive
Installation Instruction Installation Instruction
© © 2004 KONE Co 2004 KONE Corporation rporation
AM-11.65.020 AM-11.65.020
A Alll l rriig gh htts s rre es se errv ve ed d.. 3 37 7 ((4 42 2)) ((E E) ) 2 20 00 04 4--0 01 1--0 08 8
0104 0104
Motor too hot Motor too hot
Prevents new drive before Prevents new drive before
the fault is
the fault is corrected. corrected.
•• Ch Chec eck th k the ma e mach chin ine r e roo oom m
ventilation ventilation
•• Ch Chec eck t k the he re reso solv lver er an angl gle e
(measure the current) (measure the current)
•• Ch Chec eck k re resi sist stan ance ce of of th the e
thermistor circuit thermistor circuit
0105 0105
AC voltag AC voltage in the e in the
intermediate circuit is too intermediate circuit is too
low or too high.
low or too high.
Emergency stop. Emergency stop.
Prevents new drive before
Prevents new drive before
the fault is
the fault is corrected. corrected.
•• If t If the he su supp pply ly vo volt ltag age dr e drop ops s
during drive, decrease the during drive, decrease the
acceleration
rate at acceleration rate at
acceleration (6_21) acceleration (6_21)
parameter. parameter.
•• If t If thi his fa s faul ult is t is ac acti tive d ve dur urin ing g
start, check the charging start, check the charging
circuit, fuses and braking circuit, fuses and braking
transistor.
transistor.
0106 0106
Inverter not OK Inverter not OK
Prevents new drive before Prevents new drive before
the fault is
the fault is corrected. corrected.
•• Ch Chec eck c k con onne nect ctio ions ns of of
tachometer and thermal switch tachometer and thermal switch
(XM2).
(XM2).
•• T Th he e v va allu ue e ffo orr Tacho fault Tacho fault
counter (6_35) counter (6_35) parameter may parameter may
be too sensitive. Turn the be too sensitive. Turn the
elevator to RDF (machine
elevator to RDF (machine
room
inspection in North room inspection in North
America) America) and and back back to to Normal Normal
to reset the tacho fault counter. to reset the tacho fault counter.
•• If L If LBR L BR LED d ED doe oes no s not li t ligh ght, r t, ref efer er
to AS-11.65.008 and circuit to AS-11.65.008 and circuit
diagrams.
diagrams.
•• If If LB LBR l R lig ight hts b s but ut LB LBE i E is n s not ot
activated at start, check activated at start, check
(6_38). (6_38).
•• If M If MLB LB is ' is 'sh shut utdo down wn', ', ch chec eck k
voltage in the supply and X10/ voltage in the supply and X10/
16 in MLB (+24V).
16 in MLB (+24V).
•• R Re em mo ov ve e tth he e U U
REF2 REF2
jumper. jumper.
0107 0107
LWD adjustment value out LWD adjustment value out
of scale.
of scale.
Elevator controller prevents Elevator controller prevents
the drive. (Drive allows
the drive. (Drive allows
driving)
driving)
•• Ch Chec eck th k the L e LWD WD me mech chan anic ical al
adjustment and settings of the adjustment and settings of the
load values.
load values.
•• Ch Chec eck t k the he lo load ad in in ca carr..
F Fa au ulltt S Sy ym mp ptto om ms s o of f ffa au ulltt A Ac cttiio on n