Komfovent 1300 U Скачать руководство пользователя

Страница: 5 / 36

UAB KOMFOVENT we reserve the right to make changes without prior notice

RHP STANDARD_21-04

INDOORS

OUTDOORS

Filter

Heat pump

assembly

Heat pump

refrigerant

coil

Heat pump

refrigerant coil

Filter

Fan

Rotary

heat

exchanger

Fan

Electrical

heater

Heat exchangers and heaters (or coolers) are designed to compensate for heat/cool losses during

ventilation, therefore, we do not recommend using this unit as the main heating/cooling source.

The unit may fail to reach a user-defined supply air temperature when the actual temperature in the

premises differs significantly from the temperature set point, since this will lead to inefficient opera-

tion of a heat exchanger.

RHP STANDARD air handling units are manufactured in different sizes and various air flow ranges (from 400 to 1500 m

/h).

Содержание 1300 U





































Результаты поиска

Содержание 1300 U

Отзывы:

Похожие инструкции для 1300 U

Бренды по названию

Популярные бренды

Komfovent 1300 U, Руководство по установке

Результаты поиска

Содержание 1300 U

Отзывы:

Похожие инструкции для 1300 U

Бренды по названию

Популярные бренды