background image

 
 

TUBE REPLACEMENT FOR THE KOMET

19

 

 COMBO

 

 
 
The following information is for the more mechanically advanced user. Please bring your 
combo amp to a qualified technician if you do not feel comfortable with the following 
procedure.  Unplug amp from the wall. Make sure the tubes of the amp have cooled down 
sufficiently before handling. 

Note

: always wear a tube glove and safety glasses when handling 

audio tubes. 
 
Lay the combo down face forward on a flat, clean soft surface like a carpet or on the floor 
protected by a thick towel.  
 

Unplug

 the speaker cable and AC power cable from chassis. Un-screw and remove the 

six

  

(three per side) back panel screws and washers.   
 
 
! !

  WARNING  

! !

  Do not un-screw and remove the four

,

 larger chassis mounting bolts.

  

Doing so will release the amp chassis causing internal damage.  
 
 
After you have un-screws the 

six

, smaller (

three per side on back panel)

 - gently extract the panel 

mounted chassis with two hands carefully positioned from under the chassis. Be careful not to 
grip or disturb the power and pre amp tubes. 
 
Place the panel mounted chassis on a safe, flat surface and refer to this manual for the tube 
extraction and installation procedure. Install following the reverse of the chassis extraction 
procedure. 

 
 

 
SERVICING 

 
 

 

We  are  very  confident  that  your  Komet

  amplifier  is  one  of  the  most  reliable  amplifiers  ever 

built. A combined experience of many decades of amp design and service  has been applied to 
the construction all Komet

 

amplifier models. We have been inside thousands of amps and we 

have  seen  every  kind  of  problem  that  can  occur.  Great  care  has  been  taken  to  anticipate  and 
prevent  such  problems  in  your  Komet

  amplifier.  Every  part  and  component  in  this  amplifier 

has  been  carefully  chosen  for  its  specific  performance.  Some  parts  are  proprietary  or  hard  to 
find. We do not recommend replacing any  of the internal components with generic parts from 
different manufacturers.   
 
We  also  recommend  that  you  bring  your  Komet

  amplifier  to  only  a  qualified  service 

technician,  especially  if  you  should  feel  un-comfortable  changing  /  installing  audio  tubes.  
Should your Komet

 

amplifier ever need servicing or repair, please make arrangements with us 

to have your amp shipped back to Komet

 

Amplification.

 

 

 
 
Copyright 1999-2017, Komet

Amplification. Group, L.L.C.  May not be reproduced in any form without express written consent from Komet

Amplification.

 

Содержание 19
























Отзывы: