4
KOLEDA
SOLUS+
USER MANUAL
*
You will need a standard 2.4 ghz Wi-Fi bandwth . If your router has
band steering, we advise that you uncouple the 2.4 ghz and 5.0 ghz
networks. This can easily be done by logging into your Wi-Fi router IP
address!
INSTALLING YOUR SOLUS+
HEATER ON THE WALL:
• Attach the template to the wall in the position that you intend
to hang the heater ensuring the template itself is level.
• Drill the 4 holes as indicated on the template using an
appropriate sized drill bit.
• Remove the template from the wall.
• Insert raw plugs and screw in supplied mounting screws,
leaving the screw head and 4- 5mm of screw shaft exposed
(to mount the brackets on).
• The heater can now be affixed to the wall using the installed
screws by aligning the screw head with the holes on the
heater wall mount.
INSTALL ATION SAFE T Y
• This appliance must be disconnected from its power source
during installation or service activities and when replacing.
• In order to avoid overheating and potential fire hazard,
DO NOT cover the heater with insulating material or similar
material under any circumstances. DO NOT locate the
heater within 0.3m of any flammable materials (eg. Furniture,
curtains).
• The recommended minimum distance of the panel to the floor
should be 1.2m, especially if there are children at home.
• The space between the rear of the panel and the wall must be
unobstructed at all times to allow sufficient air flow.
• NEVER mount the heater where there is a risk it could fall into
any kind of water container.
• DO NOT install in rooms where direct contact with water is
possible.
• If your electric supply exceeds 250 Volts, DO NOT USE the
heater under any circumstances.
• Under ALL circumstances, the electrical circuit to power the
heater must be capable of disconnection and de-activation
by a switch, fuse, RCD or GFCI.
• DO NOT operate the heater if the cord or plug is damaged
or after the heater malfunctions, or if it has been dropped or
damaged in any manner. Check each heater for damage
before installation. Make sure that the heater itself, the plug
and the cable are free of any visible signs of damage. If the
cord is damaged the appliance must be sent for repair to the
manufacturer (SIA Green Warm Technology).
• Handle carefully and avoid stressing the glass mechanically.
Do not use the heater if the glass panels are damaged.
Disconnect the heater and do not put it into operation again.
Dismount the heater immediately to reduce the danger of
direct impact from falling pieces and dispose of the unit
in accordance with the local Waste Electrical Equipment
regulations.
• This heater must only be used for the heating of people or
buildings. The heater is not to be used by children or persons
with reduced physical, sensory or mental capabilities, or lack
of experience or knowledge. Children should be kept away
and should not be left unsupervised around the unit.
• All operators should only switch on/off the appliance
provided that it has been placed or installed in its intended
operating position in accordance with these instructions.
Children must not plug in, switch on or regulate the appliance
or perform user maintenance including cleaning.
• DO NOT touch the heater when in use. The product has a
surface temperature of around 115°C and prolonged contact
with the heater will cause burns and injury.
• IMPORTANT: The heater must be mounted on a non-
flammable surface that is capable of bearing the weight of
the heater.
CLEANING
• Before attempting to clean the panel, unplug the heater,
isolate the unit from the electrical supply and allow it to
completely cool down. DO NOT immerse the SOLUS+ in
water or splash water onto it. Clean the glass surface with a
damp cloth and glass cleaner. Never use a wet cloth. When
clean, dry the surfaces with a dry cloth.
• DO NOT apply abrasive materials, solvents or solvent wipes
to the surface as this can cause irreparable damage. Wait
until the unit is completely dry before use.
MAINTENANCE & REPAIR
• DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void your
warranty. Repairs must only be carried out by an authorised
KOLEDA service partner or the manufacturer (SIA Green
Warm Technology).