3
KOLEDA
SOLUS+
USER MANUAL
• In no case shall SIA Green Warm Technology (KOLEDA)
be liable under any legal theory, including but not limited
to contract or strict liability, for any direct, indirect special,
incidental or consequential damages resulting from incorrect
product use.
SAFET Y ADVICE
• CAUTION! Danger of electrocution. The mounting/
installation is recommended to be done by a qualified
professional.
• CAUTION! At no point should the product be disassembled.
Opening the product control box will violate the warranty
and may lead to malfunction and danger to life.
• CAUTION! There is always risk of injury from touching
any form of electric heater and SOLUS+ panels are no
different. However, a key benefit of SOLUS+ panels, unlike
conventional heaters, is that they can be mounted higher up
on walls - reducing the likelihood of accidentally touching
them or falling against them. We always advise this, especially
in areas where young children or the elderly are present.
• CAUTION! Connect and install the device only in the way
shown in these instructions. Any other method could cause
damage, injury and/or risk to life.
WHERE TO PLACE THE HEATER
• This is an infrared panel heater. It heats objects by transferring
energy directly from the heater into the object. Therefore,
consider placing the heater where it will not be immediately
obstructed by objects like furniture or where it cannot
effectively radiate out, such as at the edge or in the corners of
a room.
• Heater placement should be guided by the most actively used
areas in a room. You want to ensure the maximum comfort for
people within a room.
• Objects placed in front of the heater will heat up and can
prevent effective heat dispersion into the room. Avoid placing
the device opposite windows or open doorways.
• The mounting location should be chosen in such a way that the
glass cannot be accidentally broken and people will not be in
danger from a possible break in the glass.
• The minimum distance from the back side of the panel must be
40mm to the mounting surface. This will always be the case if
the mounting hardware provided is used.
• Objects in front of the panel must be at least 400mm away
from the sides. Failure to do so will cause excess heat to build
up behind the heater and will void the warranty. The distance
between the sides of the heater and the sides of any adjacent
heater must be a minimum of 800mm. Failure to do so could
cause excess heat to build up behind the heaters and will void
the warranty.
SHELLY THERMOSTAT
PLEASE NOTE THAT THE SHELLY THERMOSTAT
DOES NOT WORK WITHOUT THE FOVI APP
To enable the Shelly Thermostat follow the in-app instruction.
Battery Type: 3V DC - CR123A
Battery Life: Up to 18 months
Electrical consumption: Static ≤70uA/Awake ≤250mA
Humidity measurement range: 0~100% (±5%)
Temperature measurement range: -40°C ÷ 60 °C (± 1°C)
Working temperature: -40°C ÷ 60 °C
Dimensions (HxWxL): 35x45x45 mm
Radio protocol: WiFi 802.11 b/g/n
Frequency: 2400 – 2500 MHz;
Operational range: up to 50m outdoors/30m indoors
• CAUTION! Use the device only with batteries which comply
with all applicable regulations. Inappropriate batteries may
cause a short circuit in the device, which may damage it.
• CAUTION! Do not allow children to play with the device,
especially with the Power Button. Keep the devices for remote
control of SOLUS+ (mobile phones, tablets, PCs) away from
children.
• Device Wake Up: To open the device, twist the top and
bottom part of the case counter clockwise. Press the Button.
The LED should flash slowly. This means that Shelly Thermostat
is in AP mode. Press the Button again and the LED will turn off
and Shelly Thermostat will be in sleep mode.
LED States:
• LED flashing quickly - AP Mode
• LED flashing slowly - STA Mode (No Cloud)
• LED still - STA Mode (Connected to Cloud)
• LED flashing quickly - FW Update (STA mode
connected Cloud)
Factory Reset: You can return your SOLUS temperature sensor to its
Factory Settings by pressing and holding the button for 10 seconds.
Upon successful factory reset the LED will flash slowly.
Wi-fi Requirments: Works with standard 2.4Ghz Bandwidth!*