manualshive.com logo in svg

Koldwave 5KK14BEA2AA00, Руководство по обслуживанию, Страница: 36 / 64

Поделиться
Скачать
Koldwave 5KK14BEA2AA00 Скачать руководство пользователя страница 36

36 

page

Service Manual

5KK14BEA2AA00 / 5KK21BGA2AA00 / 5KK30BGA2AA00

17.  AVOID the use of adapter plugs or extension cords. If it is necessary to use an 

extension cord or an adapter plug to operate the unit, ensure that they are 
correctly rated for the applica on. Consult a local qualifi ed electrician and all 
local electrical codes to ensure proper setup. Any extension cord used with this 
device must be rated for a minimum of 15A.

18.  DO NOT unplug the unit by pulling on the electrical cord. Keep electrical cord 

away from heat sources and always completely unroll the cord to avoid over-
hea ng. If the power cord becomes damaged, a qualifi ed service agent, quali-
fi ed electrician, or similarly qualifi ed person must replace it, in order to avoid a 
hazard or shock.

19.  The fi lters must be used with the product at all  mes. When the fi lters are 

removed for cleaning, always ensure that the unit has been turned off  and 
unplugged from the electrical outlet.

20.  Regularly clean the fi lters to maintain effi

  ciency. If the fi lters are not cleaned 

regularly, the units output performance and effi

  ciency will decline and energy 

consump on will increase.

21.  DO NOT operate the unit with a damaged power cord or plug, a er it malfunc-

 ons, has been dropped or damaged.

22.  Only use in the upright posi on on an even, fl at surface. Unit must be posi-

 oned at least 24 inches (60 cm) from the nearest object in any direc on.

23.  Stop opera on immediately if abnormal noise or odor is no ced. Contact a lo-

cal service center.

24.  Appliance is not to used by children or persons with reduced physical, sensory 

or mental capabili es, or lack of experience and knowledge, unless they have 
been given supervision or instruc on.

25.  Children being supervised not to play with appliance.
26.  That the appliance shall be installed in accordance with na onal wiring regula-

 ons.

27.  If the supply cord is damaged, it must be replaced by the manufacturer, its ser-

vice agent or similarly qualifi ed persons in order to avoid a hazard.

SAVE THESE INSTRUCTIONS

DO NOT operate a unit with a damaged power cord.

WARNING

Содержание 5KK14BEA2AA00

































































Отзывы:

Нет отзывов