Koldfront TWR327ESS Скачать руководство пользователя страница 5

Thermoelectric Precautions  

This wine cooler uses thermoelectric technology rather than compression or absorption-types and there 
are several issues that need attention: 
  

 

Room temperature -  The wine cooler needs to be located in a climate controlled room.  The unit 
will perform it’s best at a room temperature of approximately 72° to 77

.  It will not cool correctly 

when the room temperature is higher than 90° or lower than 65°F. 

 

Ventilation 

– The wine cooler needs to be free standing.  It should not be recessed or built in (fully 

recessed.)  Allow enough clearance (5”) at the rear and sides of the wine cooler to allow proper 
ventilation. Lack of proper ventilation will have a negative impact on the performance of cooler.  

 

Moisture 

– The wine cooler may have some condensed water on the surface of the glass door if 

opened constantly in a moist place. This moisture will drain into the condensate tray at the back 
of the unit and may require emptying if excessive moisture is collected in a short period of time. 

 
 

Finding a good spot for your wine cooler 

Where you locate the wine cooler is critical to its performance.  Follow these guidelines: 

  

 

Install your wine cooler on a level surface that is strong enough to support it when fully loaded.  

 

Allow 5 inches (15cm) of space  at the rear  and at both sides of the  wine cooler  to allow  proper 
ventilation.   

 

This wine cooler is designed to be free standing only and should not be recessed or built-in (fully 
recessed.) 

 

Do not place heavy objects on top of the unit.  

 

Do not install the unit outside or in a moist place.  

 

Do not install the wine cooler in direct sunlight or next to heat sources. 

 

The unit’s cooling system operates at maximum efficiently with an ambient room temperature of 
72° to 77

.  The interior temperature can be set between 44°F and 66°F and will be most accurate 

in that temperature range. 

 

 

Содержание TWR327ESS






















Отзывы: