Koldfront KIM450BL Скачать руководство пользователя страница 10

 

 
Important

:

 Before you begin, unplug the ice maker or disconnect the power. 

 

Important: Once you are ready to install it in a cabinet or directly on the floor, you must adjust the 
feet to level the ice maker. 
 

 

Leveling the Ice Maker 

It is important for the icemaker to be leveled in order to work properly. It can be raised or lowered by 
rotating the four feet on the bottom of the machine. If you find that the surface is not level, rotate the 
feet until the ice maker becomes level. You may need to make several adjustments to level it. We 
recommend using a carpenter’s level to check the machine.  
1. 

Place a carpenter’s level on top of the icemaker to see if it is level from front to back and side to 
side. 

2.  Adjust the height of the feet as follows: 

 

Turn the leveling feet to the right to lower that corner of the ice maker.  
Turn the leveling feet to the left to raise that corner of the icemaker.

 

 

 
 
 
 
 
 
 
 
 

 

Reversing the Door Swing 

Tools needed: flathead screwdriver, Phillips screwdriver 
 
 
 

 

1.  Using a Phillips head screwdriver, remove the screws and take off the top hinge. Keep the 

parts together and set them aside. 

2.  Lift the door off of the bottom hinge and turn it upside down so that the handle is on the right. 

Set the door aside. 

3.  Using a flathead screwdriver, remove the plugs from the screw holes opposite the top hinge. 

Set them aside. 

4.  Using a Phillips screwdriver remove the bottom hinge and install it on the opposite side. 
5.  Position the door on the bottom hinge. 
6.  Align the door on the bottom hinge and replace the top hinge. 
7.  Replace the plugs on top and screws for the lower hinge opposite from where they were 

removed. 

 
 
 
 
 
 
 
 
 
 

Содержание KIM450BL






















Отзывы: