background image

111864-2-

BA

 (-)

Copyright 

1996 Kohler Co.

WELLWORTH

 LITE

VITREOUS CHINA

REVERSE TRAP TOILETS

BEFORE YOU BEGIN

HOW TO USE THESE INSTRUCTIONS

Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your partic-
ular installation. This will aid you in avoiding the unneces-
sary expense associated with improper installation. In
addition to proper installation, read all operating and safe-
ty instructions.

All information in these instructions is based on the latest
product information available at the time of publication.
Kohler Co. reserves the right to make changes in product
characteristics, packaging, or availability at any time with-
out notice.

These instructions contain important care, cleaning, and
warranty information - please leave instructions for the
consumer.

NOTES

Seat post holes on 5-1/2” centers.

Water depth from rim is 6-11/16”.

1-3/4” passageway.

Ensure that the new toilet has the correct
roughing-in dimension. The K-3407 has a 10”
roughing-in dimension. See Fig. #1.

Be very careful while working with vitreous china
products. Vitreous china can break and chip if
you overtighten bolts and nuts or carelessly
handle the product.

Carefully inspect new fixture for any sign of
damage.

Observe all local plumbing and building codes.

Shut off hot and cold water supplies.

For new construction, refer to the dimensions in
Fig. #1 and Fig. #4 for locating the shut-off valve.

Fixture dimensions are nominal and conform to
tolerances by ANSI Standards (A112.19.2).

WARNING: Risk of external leakage. The fill
valve nut has been factory-tightened to design
specifications. If re-tightening is required, wrench
tighten one turn past finger tight.

ORDERING INFORMATION

Bowl K-4229
Tank K-4512

When specified:

3/8” supply

K-7638

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Floor bolts (pr.)

21401

. . . . . . . . . . . . . . . . . . . . . . . . . 

Recommended elongated seat

K-4652

. . . . . . . . . . . 

Содержание WELLWORTH LITE K-4229









Отзывы: