background image

   

                                                                          

1049310-2A-A            

                                                                                                                                        2   

  

   

                                                                          

1049310-2A-A            

                                                                                                                                        3  

  

INSTALLATION CHECKOUT

CLEANING INSTRUCTIONS

All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft 

cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely 

affect the finish and are not recommended for cleaning.

Do not use abrasive cleaners or solvents on Kohler faucets and fittings. 

INSTALLATION

1

2

3
4

5

6

7

How to Install the Spout

Remove and retain the parts from the spout kit(1) according to the follow-

ing order: nut(3) and metal washer(2).

Install the O-ring(7) to the bottom of the spout through the shank. 

Fit the spout to the center hole of lavatory. Install the metal washer and 

nut. Adjust the position of the spout and securely tighten nut.

Thread the supply tee(6) with plastic gasket(5) and rubber washer(4) to 

the spout shank, tighten by hand.

How to Install the Valve Bodies, the Handles 

and the Hoses

Remove the handle kit(8) from the side body(9). Install the sticker 

washer(10) into the groove on the bottom of the escutcheon(13).

Put the washers into the ends of the hose(14). Connect the side bodies 

and supply tee(6) with hoses as shown in the figure.

NOTE: 

The hoses(14) should only be used here.

Insert the side body with dished washer (17), washer(11)and nut(12) 

through mounting holes from bottom of the lavatory(For 14406T-4 and 

14408T-4, the side body with red mark on the left when facing the front of 

the faucet). Press the spline adapter(15) onto the valve stem(16).

Reinstall and tighten the handle kit(The handle with the red washer on 

the left when facing the front of the faucet). Tighten the nut(12).

The configuration shown is the correct position of the handles in the 

closed position.

8

9

14

11

12 17

14

9

6

13

10

15
16

34

Ensure that all connections are tight. Remove the aerator(34). 

Open the drain. Turn on the main supply and check for leaks. Open both 

hot and cold valves and run water through the spout to remove any 

debris. Turn the valve off. Reinstall the aerator.

How to Install the Drain

Remove the stopper(18), flange(20) and washer(21) from the drain 

body(23). Take off the tailpiece(25). Apply thread tape to the tailpiece 

and install the tailpiece to drain body. Insert the drain body kit into the 

lavatory from underside, and make sure the drain lever hole(22) facing to 

the back of the lavatory. Screw the flange with washer into the drain 

body. Tighten the locknut(24) by hand from underside of the lavatory.

NOTE: 

If needed, apply a ring of plumbers putty around the underside of 

the drain flange(20), instead of using washer(21).

Place the stopper(18) into the drain body aligning the flat side of stopper 

hole(19) with the drain lever hole.

Remove the retaining nut(29). Fit the plastic washer(27) and retaining nut 

onto the ball lever(28). Insert the ball lever assembly into the drain lever 

hole and through the stopper hole. Tighten the retaining nut.

Be sure that the ball lever(28) points to the back of the lavatory, tighten 

the locknut(24) on the drain body by wrench. 

NOTE:

 Do not reposition the drain if plumbers putty applied after the 

locknut is tightened, or you may break the putty seal. Wipe away excess 

plumbers putty.

Insert lift rod(30) to the hole at the rear of the body(33). Assemble the 

thumb screw(31) to the link(32), and link onto the ball lever(28) with 

“V”-clip (26). Slide the lift rod(30) into the hole in link. Push the ball lever 

down into the open position, and adjust the lift rod. Tighten the thumb 

screw(31).

20

21

24

18
19

21

25

22

20

23

24

29

27

26

28

28

32
26

31

30

30

33

10

mm

Отзывы: