background image

12.

NOTE: 

Water source provided must be a minimum 

of 20 litres per minute at 20psi

7.  Connect high pressure hose (C) to pump outlet

(I).

WARNING! 

To reduce the possibility of con

-

tamination always protect against backflow 

when connected to a potable water system.

8.  Choose the correct nozzle for the job to be

performed. See ‘How To Use spray Wand’ instruc-

tions on page 14.

NOTE:

 

If applying a chemical or cleaning solution, 

see ‘Applying Chemicals & Solvents’ on page 15.

9.  Turn water source on.

NOTE:

 

Risk of property damage. Failure to do so 

could cause damage to the pump.

10. Remove all air from the pump and high pressure

hose by depressing trigger until a steady stream

of water is present.

11. Start engine. See Engine Owner’s Manual for

correct procedure.

WARNING!

 

Risk of unsafe operation. If 

engine does not start after two pulls, squeeze 

trigger of gun to relieve pump pressure. Pull 

starter cord slowly until resistance is felt. 

Then pull cord rapidly to avoid kickback and 

prevent hand or arm injury.

Note:

 

If the oil level in the engine is low, the engine 

will not start. If the engine does not start, check the 

oil level and add oil as needed.

12. Depress trigger on gun to start water flow.

WARNING!

 

Risk of unsafe operation. Stand 

on a stable surface and grip gun/spray wand 

firmly with both hands. Expect the gun to kick 

when triggered.

13. Release trigger to stop

water flow.

WARNING! 

Risk of injury from spray. Always  

engage the trigger lock (P) when gun is not in 

use. Failure to do so could cause accidental 

spraying 

Shutting Down

1.  After each use, if you have applied chemicals,

place detergent siphon hose into container of

clean water and draw clean water through chemi-

cal injection system to rinse system thoroughly.

NOTE: 

Risk of property damage. Failure to do so 

could cause damage to the pump.

2. Turn engine off. See Engine Owner’s Manual.

NOTE:

 

Risk of property damage. NEVER turn the 

water off with the engine running.

3.  Turn water source off.

4.  Pull trigger on spray gun to relieve any water

pressure in hose or spray gun.

7109782 PS3395 EuroQuip Manual.indd   12

4/4/2017   9:44:00 AM

Содержание Powershot PS3395






























Отзывы: