Kohler ODEON K-8766 Скачать руководство пользователя страница 2

Страница: 2 / 8

ROUGHING-IN

INSTALLATION

1. REMOVE EXISTING TOILET

Turn off water supply. Flush the toilet and use a sponge to remove the remaining water from the tank and bowl. Disconnect the supply
shut-off valve (if present) and remove the old tank and bowl.

2. ASSEMBLE TANK BOLTS & WASHERS

Slip bolt heads into mounting hole on bottom of tank. Place large foam washer on base of flush valve. See Fig. #2a. Place tank on
bowl and attach with nuts & washers from under bowl. See Fig. #2b.

1037406-LM01-B -2-

Fig.#1

202

786

390

475

305

102

S-trap

8766LM

733

350

257

364

163

155

430

390

704

340

262360

166

155

430

391

202

782

386

396

180

160

102

P-trap

8711LM

All dimensions in mm. Fixture dimensions are nominal and conform to tolerances as per ASME Standard A112. 19.2M.

Product pictures shown are representative only, actual products may vary.

Kohler reserves the right to make changes in product characteristics, packaging or availability at any time without notice.

Содержание ODEON K-8766









Результаты поиска

Содержание ODEON K-8766

Отзывы:

Похожие инструкции для ODEON K-8766

Бренды по названию

Популярные бренды

Kohler ODEON K-8766, Руководство по установке

Результаты поиска

Содержание ODEON K-8766

Отзывы:

Похожие инструкции для ODEON K-8766

Бренды по названию

Популярные бренды