1206124-2A-C
2
1206124-2A-C
3
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
How to Install the Spout
Remove the center tee(9), the nut(6) and the washer(5) from the
shank(2). Leave the rubber washer(7) and the plastic gasket(8) in the
center tee.
Slide the escutcheon(3) onto the bottom of the spout kit(1) through the
shank. Slide the rubber washer(4) into the bottom groove of the
escutcheon. Insert the lift rod(10) to the back hole on the faucet. Then fit
the spout kit into the center hole of lavatory. From underside of the
lavatory, install the washer(5) and the nut(6). Position the spout. Secure
the spout kit by tightening nut. Reinstall the center tee.
How to Install the Valve Bodies and Handles
Put the nut(21) and metal washer(20) onto each side body(22). Insert
side bodies through mounting holes from bottom of the lavatory(
NOTE:
The valve body with red dot should be installed on the left, and the valves
are in the closed position before installing them).
Install the rubber washer(17) and the escutcheon(16) onto each side
body. Press the spline adapter(18) onto each valve stem(19), then press
the handle(15) onto each spline adapter. Secure the handles by the
screws(13) with the washers(14). Press the plug(12) into the hole on the
top of each handle, the plug with ‘H’ mark is on the left. Wrench tighten
the nuts(21).
One end of the hose(23) connect to the outlet of side body, and the other
end connect to the center tee(9).
Ensure that all coupling nuts are tight. Ensure that the lever handles are
in the off position. Turn on the main water supply and drain, and check for
leaks. Repair as needed.
Remove the aerator(38) by key(39). Run hot and cold water through
faucet for about one minute to remove any debris. Check for leaks.
Repair as needed. Remove any debris from the aerator. Shut off the
faucet. Reinstall the aerator.
NOTE:
If needed, apply a ring of plumbers putty around the underside of
the drain flange(26), instead of using washer(27).
Place stopper(24) into drain body aligning the flat side of stopper hole(25)
with the drain lever hole.
Remove the retaining nut(33). Fit the plastic washer(34) and retaining nut
onto the ball lever(35). Insert the ball lever assembly into the drain lever
hole and through the stopper hole. Tighten the retaining nut.
Be sure that the ball lever(35) points to the back of the lavatory, tighten
the locknut(30) on the drain body by wrench.
NOTE:
Do not reposition the drain if plumbers putty applied after the
locknut is tightened, or you may break the putty seal. Wipe away excess
plumbers putty.
Assemble thumb screw(36) to link(37), and link onto ball lever rod(35)
with ‘V’-clip(32). Slide lift rod(10) into the hole in link. Push the ball lever
down into the open position, and adjust the lift rod. Tighten thumb
screw(36).
How to Install the Drain
Remove stopper(24), flange(26) and washer(27) from drain body(29).
Take off the tailpiece(31). Apply thread tape to tailpiece and install the
tailpiece to drain body. Insert drain body kit into the lavatory from
underside, and make sure the drain lever hole(28) facing to the back of
the lavatory. Screw the flange with washer into the drain body. Tighten
the locknut(30) by hand from the underside of the fixture.
1
2
3
7
8
9
9
10
4
16
15
14
13
12
17
18
19
20
21
22
23
5
6
26
27
30
24
25
27
31
28
26
29
39
38
30
33
34
32
35
35
37
32
36
10
