112363–2–
AA
(0793)
Copyright
1993 Kohler Co.
FLEUR
WATERGUARD
VITREOUS CHINA TOILET
K-3417-**-AA
1. BEFORE YOU BEGIN
HOW TO USE THESE INSTRUCTIONS
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your partic-
ular installation. This will aid you in avoiding the unneces-
sary expense associated with improper installation. In
addition to proper installation, read all operating and safe-
ty instructions.
All information in these instructions is based on the latest
product information available at the time of publication.
Kohler Co. reserves the right to make changes in product
characteristics, packaging, or availability at any time with-
out notice.
These instructions contain important care, cleaning, and
warranty information please leave for the consumer.
INSTALLER HAZARD NOTIFICATION
WARNING: Risk of injury or product damage.
Handle vitreous china products very carefully.
Vitreous china can break and chip if you
over-tighten bolts and nuts.
NOTE: Follow all local plumbing and electrical codes.
PRODUCT PROPERTIES
Vitreous china 2-piece toilet.
Distance from rim to water surface is 6-3/4”.
2” passageway.
For roughing-in and overall dimensions, see
Fig. #2.
Fixture dimensions are nominal and conform to tol-
erances by ANSI standards (A112.19.2).
PRODUCT REQUIREMENTS
The toilet MUST have a 3/8” I.D. water supply that
is 10-1/4” above the floor and 5-1/8” left of the clos-
et flange centerline. 25 p.s.i. running pressure is re-
quired at the shut-off valve.
Since all toilets do not have the same supply rough-
in, you may have to change the location of the sup-
ply stop to install this toilet.
Closet flange must be 12” on-center from wall.
Seat post holes are on 5-1/2” centers.
ORDERING INFORMATION
Fleur
Waterguard
Toilet Bowl
K-4227-**-AA
. . . . . . . .
Tank with Tank Cover
K-4586-**-AA
. . . . . . . . . . . . . . . . .
Tank Cover
80006-**-AA
. . . . . . . . . . . . . . . . . . . . . . .
Bolt Caps
52048-**-AA
. . . . . . . . . . . . . . . . . . . . . . . .
Float Valve
30672-AA
. . . . . . . . . . . . . . . . . . . . . . . . .
Flush Valve
500176-AA
. . . . . . . . . . . . . . . . . . . . . . . .
Actuator
500173-AA
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat and cover
82836-**AA
. . . . . . . . . . . . . . . . . . . . .
When specified:
3/8” supply
K-7638-AA
. . . . . . . . . . . . . . . . . . . . . . . .
Floor bolts (pr.)
21401-AA
. . . . . . . . . . . . . . . . . . . . . .
NOTE: For service parts ordering information, see sepa-
rate Service Parts document enclosed with product.
MATERIALS REQUIRED
Closet flange
Toilet gasket (wax seal)
Toilet T-bolts (2) 5/16” diameter
Toilet setting compound (optional)
Toilet supply shut-off valve, 3/8” required
TOOLS REQUIRED
10” adjustable wrench
12” pipe wrench
Screwdriver
Tape Measure
Tubing cutter
Level
Putty knife
Hacksaw/metal file (for shortening T-bolts)
NOTE: Site preparation may require additional tools.
