Kohler Command PRO CV682 Скачать руководство пользователя страница 64

Страница: 64 / 68

Install External Governor Controls

1. Install governor lever onto governor cross shaft.
2. Connect choke linkage into bushing/lever from back.

Make certain that control shaft offset is back.

Connect throttle linkage and spring to governor

lever.

3. Move governor lever toward carburetor as far as it

will go (wide-open throttle) and hold in position.

4. Insert a long thin rod or tool into hole on cross shaft

and rotate shaft counterclockwise (viewed from end)

as far as it will turn, then torque nut to 6.8 N·m

(60 in. lb.).

5. Connect governor spring from throttle control lever to

appropriate hole in governor lever. Connect

governed idle spring from governed idle bracket to

G-hole in governor lever. Refer to Governor Lever

and Hole Position/RPM Chart. Note that hole

positions are counted from pivot point of governor

lever.

Governor Lever Hole Position

Governor Lever

Governed Idle Hole

Hole 1

Hole 2

Hole 3

Hole 4

Governor Lever and Hole Position/RPM Chart

(Governed Idle, 10% Regulation)

High Idle

RPM

Governor Lever

Hole No.

Governor

Spring Color

Code

4200

Black

4000

Purple

3950

Purple

3900

Green

3850

Green

3800

Red

3750

Red

3700

Green

3650

Green

3600

Red

3550

Red

3500

Clear

3450

Clear

3400

Clear

3350

Clear

3300

Clear

Install Electric Starter Motor

1. Install starter motor using screws. Position lift

bracket to also secure dipstick tube.

2.  Torque screws to 15.3 N·m (135 in. lb.).
3.  Connect leads to solenoid.
4.  Install dipstick tube and align mounting hole with

threaded hole in lift bracket. Secure with M5 screw.

Torque screw to 4.0 N·m (35 in. lb.).

Reassembly

24 690 37 Rev. B

KohlerEngines.com

Содержание Command PRO CV682




































































Результаты поиска

Содержание Command PRO CV682

Отзывы:

Похожие инструкции для Command PRO CV682

Бренды по названию

Популярные бренды

Kohler Command PRO CV682, Руководство по обслуживанию

Результаты поиска

Содержание Command PRO CV682

Отзывы:

Похожие инструкции для Command PRO CV682

Бренды по названию

Популярные бренды