Kohler 4EFCD-Low CO Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 88

background image

TP-6391 9/08

15

Section 2 Scheduled Maintenance

Section 2 Scheduled Maintenance

Accidental starting.
Can cause severe injury or death.

Disconnect the battery cables before
working

on

the

generator

set.

Remove the negative (--) lead first
when

disconnecting

the

battery.

Reconnect the negative (--) lead last
when reconnecting the battery.

WARNING

Disabling the generator set.

Accidental starting can

cause severe injury or death.

Before working on the

generator set or connected equipment, disable the generator
set as follows: (1) Move the generator set master switch to the
OFF position. (2) Disconnect the power to the battery charger.
(3) Remove the battery cables, negative (--) lead first.
Reconnect the negative (--) lead last when reconnecting the
battery. Follow these precautions to prevent starting of the
generator set by an automatic transfer switch, remote
start/stop switch, or engine start command from a remote
computer.

Hazardous voltage.
Can cause severe injury or death.

Operate the generator set only when
all guards and electrical enclosures
are in place.

Moving parts.

WARNING

Alternator Service.

Under normal operating conditions

the generator set alternator does not require scheduled
service. Refer to the service schedule for items that
require maintenance.

Engine Service.

Perform generator set engine service

at the intervals specified by the engine service literature.
Contact an authorized Kohler

r

service distributor/

dealer to obtain engine service literature.

Generator Set Service.

See the Safety Precautions

and Instructions at the beginning of this manual before
attempting to service, repair, or operate the generator
set. Have an authorized Kohler

r

service distributor/

dealer perform all generator service.

Routine Maintenance.

Refer to the following generator

set service schedule, the engine service schedule, and
the runtime hours displayed on the ADC 2100 to
determine when to schedule routine maintenance.
Service the generator set more frequently if it is subject
to extreme weather, long operating hours, or dusty or
dirty conditions.

Service Schedule.

Perform maintenance on each item

in the service schedule at the designated interval for the
life of the generator set.

Tools.

Tools and instruments used to perform some

maintenance items are not generally available to the
generator set owner.

Therefore,

have service

performed by an authorized distributor/dealer.

2.1 General

Perform the items listed in the service schedule at the
designated intervals for the life of the generator set. For
example, an item serviced every 100 hours or 3 months
must also be serviced after 200 hours or 6 months,
300 hours or 9 months, etc.

Note:

See the generator set operation manual and the
engine service manual for service procedures not
included in this manual.

«
...
13
14
15
16
17
...
»

Содержание 4EFCD-Low CO

























































































Отзывы:

Нет отзывов

Похожие инструкции для 4EFCD-Low CO

Бренд: Hubner Страницы: 28

Бренд: Hewalex Страницы: 2

Бренд: 3onedata Страницы: 7

Бренд: Encore Страницы: 27

Бренд: Oriental motor Страницы: 56

Бренд: Linear Technology Страницы: 26

Бренд: Inter-m Страницы: 20

DIGITAL plus LC100

Бренд: Lenz Страницы: 8

SUNNY BOY 3000-US

Бренд: SMA Страницы: 36

Бренд: Tektronix Страницы: 11

Бренд: tams elektronik Страницы: 28

Бренд: Patton electronics Страницы: 20

Бренд: Aurora Design Страницы: 2

Бренд: Mastervolt Страницы: 28

Бренд: Xantrex Страницы: 21

Бренд: ICP DAS USA Страницы: 2

JNTHBCBA0001BEAU

Бренд: TECO Страницы: 98

SoundDock Series II

Бренд: Bose Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды