background image

TP-5695 12/93

Parts Ordering Instructions 8-1

Section 8. Parts Ordering Instructions

For service or information, check the yellow pages of the
telephone

directory

under

the

heading

GENERATORS--ELECTRIC or contact the local marina
for the authorized Kohler service dealer/distributor in the
area.

KOHLER CO. KOHLER, WISCONSIN 53044
PHONE 414-565-3381
FAX 414-459-1646 (North American Sales),
414-459-1614 (International)
FOR SALES & SERVICE IN U.S.A. & CANADA PHONE
1-800-544-2444

A major service manual and parts catalog may be
ordered through an authorized Kohler service
dealer/distributor. When ordering, state MODEL and

SPEC. numbers from the Generator Nameplate. (See
NO TAG.)

In any communications regarding this generator set,
please report the MODEL, SPEC. and SERIAL numbers
as found on the nameplate attached to the generator
and engine. Enter numbers in spaces provided below.
This information will enable the authorized Kohler
service dealer/distributor to supply the correct part or
data for this particular model.

Model No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specification No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Serial No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engine No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Содержание 3.5CFZ, 4CZ, 5CFZ, 6.5CZ


















































































Отзывы: