X582205 Ver.6.0
Ver. 6.0
Linear Orifi ce
Shock Absorber
KSHJ
Series
7.
Ensure that the hardness of the surface directly impacting
the piston rod of the shock absorber is over HRc40
(excluding models with cap).
8.
Be aware that performance and characteristics change
depending on the operating temperature.
4.
For swing impacts, ensure that the angle of eccentricity
between the load direction and the center line of the shock
absorber is at or below the specification values shown as
following. For
KSHJ14
×
12
(
C
) (outer diameter M14) or
smaller models, 1
°
or bellow. For
KSHJ16
×
15
(
C
) (outer
diameter M16) or larger models, 3
°
or bellow.
(
For
KSHJ42
×
70
(
C
) models, 1
°
or bellow. )
5.
The small screw on the back end of the shock absorber
should never be loosened or removed. Oil may leak out of
the shock absorber leading to a loss of functionality and
resulting in damage to the equipment and accidents.
1.
Mount the shock absorber so that the load contacts at the
center of the rod, and it is not subjected to off-centered loads.
An off-centered load could result in breakage or defective rod
returns.
2.
To adjust the capacity with the stroke, adjust the stopper nut
(-S) or add an external stopper.
3.
If using with a cap, always mount a stopper nut (-S) or an
external stopper to ensure that the cap is not subjected to
loads at the stroke end. The stopper nut mounting position
must not exceed the distance shown in the table below.
You can use it without a stopper nut or external stopper, but
over the long-term, the stop location changes due to cap
deformation and wear.
6.
When mounting the shock absorber, always use the following
maximum tightening torque guidelines. Tightening using
excessive force may result in damage.
Mounting
Cover the unit when mounting it in locations where it might be subject
to excessive dust, dripping water, dripping oil, etc. Dents, scratches,
water, oil, or dust on the piston rod results in damage and decreases
service life.
General precautions
Thank you for purchasing this Koganei product.
Before using it, be sure to read this manual and make sure you use it correctly.
Keep this manual in a safe place for future reference.
Instruction Manual
6/’16 KG
* For other details about specifications and precautions, see the catalog.
* For inquiries about the product, contact the Koganei overseas department at the
number below.
OVERSEAS DEPARTMENT
3-11-28, Midori-cho, Koganei City, Tokyo 184-8533, Japan
Tel: 042-383-7271 Fax: 042-383-7276
2
Outer diameter
of nut
Hook the wrench into the
groove on the nut to use it
Hook wrench
Note: The
KSHJ45
×
50
(
C
) use nominal number AN09 mounting nut
prescribed in JIS B1554 (nuts for rolling bearings). Use a hook
wrench (nominal 58 to 65 or 65 to 70) for tightening.
Model
Maximum tightening torque
KSHJ4
×
3
（
C
）
0.5
KSHJ6
×
4
（
C
）
KSHJ6
×
6
（
C
）
0.85
KSHJ8
×
4
（
C
）
KSHJ8
×
5
（
C
）
KSHJ8
×
8
（
C
）
2.5
KSHJ10
×
6
（
C
）
KSHJ10
×
10
（
C
）
KSHJ10
×
15
（
C
）
6.5
KSHJ12
×
6
（
C
）
KSHJ12
×
10
（
C
）
8.0
KSHJ14
×
8
（
C
）
KSHJ14
×
12
（
C
）
12.0
KSHJ16
×
8
（
C
）
KSHJ16
×
15
（
C
）
20.0
KSHJ18
×
16
（
C
）
25.0
KSHJ20
×
10
（
C
）
KSHJ20
×
16
（
C
）
30.0
KSHJ22
×
25
（
C
）
35.0
KSHJ25
×
25
（
C
）
KSHJ27
×
25
（
C
）
42.0
KSHJ30
×
30
（
C
）
KSHJ33
×
30
（
C
）
60.0
KSHJ36
×
50
（
C
）
72.0
KSHJ42
×
50
（
C
）
KSHJ42
×
70
（
C
）
KSHJ45
×
50
（
C
）
Note
85.0
KSHJ48
×
50
（
C
）
120.0
N
･
m
mm
Model
A
KSHJ4
×
3C
3
KSHJ6
×
4C KSHJ8
×
4C
4
KSHJ8
×
5C
5
KSHJ6
×
6C KSHJ10
×
6C KSHJ12
×
6C
6
KSHJ8
×
8C KSHJ14
×
8C KSHJ16
×
8C
8
KSHJ10
×
10C KSHJ12
×
10C KSHJ20
×
10C
10
KSHJ14
×
12C
12
KSHJ10
×
15C KSHJ16
×
15C
15
KSHJ18
×
16C KSHJ20
×
16C
16
KSHJ22
×
25C KSHJ25
×
25C KSHJ27
×
25C
25
KSHJ30
×
30C KSHJ33
×
30C
30
KSHJ36
×
50C KSHJ42
×
50C
KSHJ45
×
50C KSHJ48
×
50C
50
KSHJ42
×
70C
70
A
