Kodak DryView 6800 Скачать руководство пользователя страница 124

Страница: 124 / 326

DIAGNOSTICS

Status Messages and Error Codes

30JUL07

8F2919

Page

124 of 326

FE Action

Do the actions below in sequence. If an action provides a resolution, do not continue with the
other actions.

De-energize then energize the LASER IMAGER.

Do the following:

Check:

If an existing problem:

FILM CARTRIDGE

Install a new FILM CARTRIDGE.

For a film jam.

Remove films.

For an obstruction.

Remove the obstruction.

CONNECTORS and CABLES Seat all CONNECTORS.

For dirty ROLLERS.

Clean the ROLLERS.

ROLLERS

Install new ROLLERS.

E-RINGS on MOTORS and
ROLLERS

Install new E-RINGS. See the ILLUSTRATED PARTS
LIST,

PICKUP AY - ROLLERS and DRIVE Section

BLINDMATE CONNECTOR

Adjust THE BLINDMATE. See the ADJUSTMENTS AND
REPLACEMENTS,

BLINDMATE BRACKET

PICKUP FILM AT FEED
SENSOR - use the SERVICE
TOOL

Install a new SENSOR. See the ADJUSTMENTS AND
REPLACEMENTS,

SENSOR, FILM AT FEED (S5) -

PICKUP AY

PICKUP FEED ROLLER
OPEN/CLOSE MOTOR - use
the SERVICE TOOL

Install a new MOTOR. See the ADJUSTMENTS AND
REPLACEMENTS,

MOTOR, FEED ROLLER OPEN/

CLOSE (M1) - PICKUP AY

PICKUP FEED ROLLER
DRIVE MOTOR

Install a new MOTOR. See the ADJUSTMENTS AND
REPLACEMENTS,

MOTOR, FEED ROLLER DRIVE

(M2) - PICKUP AY

FEED ROLLER DRIVE
MOTOR BELT

Install a new BELTS. See the ADJUSTMENTS AND
REPLACEMENTS,

BELTS, ROLLER DRIVE and

ROLLER OPEN/CLOSE - PICKUP AY

PICKUP DRIVE MOTOR

Install a new MOTOR. See the ADJUSTMENTS AND
REPLACEMENTS,

MOTOR, DRIVE (M3) - PICKUP AY

Содержание DryView 6800







































































































































































































































































































































Результаты поиска

Содержание DryView 6800

Отзывы:

Бренды по названию

Популярные бренды

Kodak DryView 6800, Руководство по диагностике

Результаты поиска

Содержание DryView 6800

Отзывы:

Бренды по названию

Популярные бренды