Kobold NBK-01 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 16

Kobold NBK-01 Скачать руководство пользователя страница 6

NBK-01

page 6

NBK-01 K05/0322

6. Mechanical Connection

Remove the bottom flange from the
bypass  tube,  and  insert  the
cylindrical float in the NBK bypass
tube  with  the  designation  "TOP"
upturned.  Reposition  the  gasket
and close the bottom flange again;
firmly tighten with screws.
Mount  the  bypass  tube  to  the
vessel  to  be  monitored  via  the
process  connection  and  seal  with
an  appropriate  device.  Normally  it
is sufficient to fix the complete NBK
with  both  process  connections.
However  the  NBK  should  be
subjected  to  constant  shock  or
strong

vibrations

it

is

recommended  that  the  instrument
is  secured  with  rubber-damped
tube clips. No welding is allowed on
the bypass tube.

Mount  and  tighten  the

magnetic

roller indicator

- if not already

mounted - on the bypass tube with
the two provided ribbon clamps.

Mount and tighten the

reed switch

- if available - on the bypass tube at
the  opposite  side  of  the  roller
indicator  with  the  provided  ribbon
clamps  (ex  contact:  two  ribbon
clamps).  The  height  of  the  switch
contacts  may  be  selected  at  will.
The  cable  connection  must  point
downwards.  The  switch  must  be
attached close to the bypass tube.
The switching function of the switch
is impaired by an enlarged air gap.

«
...
4
5
6
7
8
...
»

Содержание NBK-01

















Отзывы:

Нет отзывов