Kobold NBK-01 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 16

Kobold NBK-01 Скачать руководство пользователя страница 10

NBK-01

page 10

NBK-01 K05/0322

8. Commissioning

Because of the setting behaviour of seals, all screw connections must be
retightened.
Fill vessel and switch on electrical controller, if available. If there are gate valves
between bypass process connection and tank, first slowly open the upper valve
(pressure equalisation) and then the lower valve (liquid side). If vent and drain
valves have been installed, close them before filling.
The liquid that now enters the bypass tube raises the float until the level between
tank and bypass tube is balanced. The roller indicator indicates the liquid level.

Commissioning electrical reed switches NBK-R

Function of switches

All switches have three connection poles (black (2), blue (1) and brown (3)).
The black wire (2) is the common pole for both switching functions
(N/C and N/O contact).
The float must pass the switch once in both directions so that the switching function
is in line with the terminal connection diagram and table below.
These instructions are often ignored when an alarm lamp is connected directly with
the result that the alarm lamp incorrectly indicates a fault.
When the switch has been passed, it is ready for operation and requires no
maintenance.

black (2) / blue (1)

black (2) / brown (3)

float above

open

closed

float below

closed

open

Hysteresis

Hysteresis is the difference between contact closing
and opening points. A hysteresis of approximately
15 mm float travel is achieved by factory tuning of the
float magnet and contact strength.

«
...
8
9
10
11
12
...
»

Содержание NBK-01

















Отзывы:

Нет отзывов