Kobalt SM1815LW Скачать руководство пользователя страница 7

Страница: 7 / 44

●

Do not use the saw until the table is clear of all tools, wood scraps, etc., except for the

workpiece.

Small debris or loose pieces of wood or other objects that contact the revolving

blade can be thrown with high speed.

●

Cut only one workpiece at a time.

Stacked multiple workpieces cannot be adequately

clamped or braced and may bind on the blade or shift during cutting.

●

Ensure the miter saw is mounted or placed on a level, firm work surface before use.

level and firm work surface reduces the risk of the miter saw becoming unstable.

●

Plan your work. Every time you change the bevel or miter angle setting, make sure the

adjustable fence is set correctly to support the workpiece and will not interfere with

the blade or the guarding system.

Without turning the tool "ON" and with no workpiece on

the table, move the saw blade through a complete simulated cut to assure there will be no

interference or danger of cutting the fence.

●

Provide adequate support such as table extensions, saw horses, etc. for a workpiece

that is wider or longer than the table top.

Workpieces longer or wider than the miter saw

table can tip if not securely supported. If the cut-off piece or workpiece tips, it can lift the lower

guard or be thrown by the spinning blade.

●

Do not use another person as a substitute for a table extension or as additional

support.

Unstable support for the workpiece can cause the blade to bind or the workpiece to

shift during the cutting operation pulling you and the helper into the spinning blade.

●

The cut-off piece must not be jammed or pressed by any means against the spinning

saw blade.

If confined, i.e. using length stops, the cut-off piece could get wedged against the

blade and thrown violently.

●

Always use a clamp or a fixture designed to properly support round material such as

rods or tubing.

Rods have a tendency to roll while being cut, causing the blade to "bite" and

pull the work with your hand into the blade.

●

Let the blade reach full speed before contacting the workpiece.

This will reduce the risk of

the workpiece being thrown.

●

If the workpiece or blade becomes jammed, turn the miter saw off. Wait for all moving

parts to stop and disconnect the plug from the power source and/or remove the battery

pack. Then work to free the jammed material.

Continued sawing with a jammed workpiece

could cause loss of control or damage to the miter saw.

●

After finishing the cut, release the switch, hold the saw head down and wait for the

blade to stop before removing the cut-off piece.

Reaching with your hand near the coasting

blade is dangerous.

●

Hold the handle firmly when making an incomplete cut or when releasing the switch

before the saw head is completely in the down position.

The braking action of the saw

may cause the saw head to be suddenly pulled downward, causing a risk of injury.

●

Do not use

this saw to cut tree limbs or logs.

●

Never

use blades recommended for operation at less than 5000 RPM.

WARNING: Additional warnings are listed throughout this manual. Please review all

before operating this power tool.

Содержание SM1815LW













































Результаты поиска

Содержание SM1815LW

Отзывы:

Похожие инструкции для SM1815LW

Бренды по названию

Популярные бренды

Kobalt SM1815LW, Руководство пользователя

Результаты поиска

Содержание SM1815LW

Отзывы:

Похожие инструкции для SM1815LW

Бренды по названию

Популярные бренды