Kobalt SM1815LW Скачать руководство пользователя страница 24

Страница: 24 / 44

● WARNING: Do not attempt to repair or

disassemble the laser. If unqualified

persons attempt to repair this laser

product, serious injury may result. Any

repair required on this laser product

should be performed by a qualified

service dealer.

NOTE:

If laser labels are missing, damaged or

not clear, contact with the Customer Service

Department for replacements.

LASER GUIDE ADJUSTMENT

(FIG. 22, 23, 24, 25)

NOTE:

All the adjustments for the operation of

this machine have been completed at the factory.

Due to normal wear and use, some occasional

readjustments may be necessary.

To prevent serious injury, insert a padlock

(not provided) or chain with padlock through

the hole in the ON/OFF Trigger Switch prior

to making any laser adjustment. DO NOT

remove the lock from the ON/OFF Trigger

Switch during any laser adjustment.

Checking Laser Line Alignment

(Fig. 22, 24)

●

Set the saw to a 0° miter and 0° bevel

setting.

●

Use a combination square to mark a 90°

angle running across the top and down the

front of a board. This line will serve as the

pattern line (Fig. 24) to adjust the laser.

Place the board on the saw table.

●

Carefully lower the saw head down to align

the saw blade with the pattern line. Position

the saw blade to the left, center or right

side of the “pattern line” depending on your

preference for the laser line location. Lock

board in place with hold-down clamp.

●

With the saw plugged in, turn on the laser

guide. Your saw has been preset with the

laser line to the left side of the blade.

When making laser line adjustments,

keep fingers away from the ON/OFF

trigger switch to prevent accidental

starting and possible serious injury.

TOP VIEW

WARNING

Cutting line

Workpiece

Laser line

Cutting line

Blade

Laser line

Содержание SM1815LW













































Результаты поиска

Содержание SM1815LW

Отзывы:

Похожие инструкции для SM1815LW

Бренды по названию

Популярные бренды

Kobalt SM1815LW, Руководство пользователя

Результаты поиска

Содержание SM1815LW

Отзывы:

Похожие инструкции для SM1815LW

Бренды по названию

Популярные бренды