Knox MedVault Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 12

Knox MedVault Скачать руководство пользователя страница 7

MedVault

®

Hardware Installation Instructions

OPE-MVHDWR-0202-H

The Knox Company ▪ MedVault

®

▪ 5

Specifications

Hardware

Weight

Approximately eighteen (18) pounds

Exterior Dimensions

9 ¼” Height X 12” Width X 9” Depth

Interior Dimensions

7 ½ Height X 10 ½” Width X 6 ½ Depth

Versions



Surface mount



Recessed version (one-inch flange around the box perimeter)

4-Pin Din Connector

USB port, which collects Audit Trail history information. It also
downloads new configuration information into the box, such as PIN
codes

.

RP-SMA Connector

Connect a WiFi antenna for wireless network if equipped.

RJ-45 Dongle

Connect a Cat5 Ethernet cable for wired networking if equipped.

Override Manual Key

If the electronics fail or the vehicle loses power, the unit can ONLY be
opened using the manual override key. For security purposes, the
manual override key is shipped separate from the unit. If you do not
receive your manual override key, contact Knox immediately.

Electronics

Temperature Range

-40º C to +80 º C (-40 º F to 176V F)

Power Supply
Input Range

10 to 15 volts DC @ 3 amps

Current Drain
(Standby)

120 milliamps

Current Drain
(Door Release)

Up to 3 amps

Current Drain
(Door Open)

150 milliamps

Initial Power
Stabilization Time

5 seconds

Absolute Max Input

20 volts DC

«
...
5
6
7
8
9
...
»

Содержание MedVault













Отзывы:

Нет отзывов