Knog NERD 12 Скачать руководство пользователя страница 4

4

DATA SETTING PROCESS (Fig 1.1)

1. All user-input data is adjusted for each digit separately. 

The current digit to be set will flash. 

2. Press 

A

 to increase the digit value by 1.

3. Hold  down 

A

  for  2  seconds  to  advance  to  the  next 

digit.

4. Press 

B

 to store the on-screen data and advance to the 

next data setting.

5. Once all data setting is complete, hold down 

B

 for 2 

seconds to exit the data setting mode. This can also be 
done at any point whilst in data setting mode, leaving 
the remaining un-set data with a   reading.

INITIATING THE COMPUTER (ALL CLEAR) (Fig 1.2) 

1. A  battery  is  already  loaded  in  the  main  unit  when 

purchased. Hold down 

A

 and 

B

 simultaneously for 3 

seconds to initiate the computer and clear all data.

 

It is important to initiate the computer before first 

usage to prevent the computer producing errors.

2. The LCD segments will be tested automatically after the 

unit is initiated.

3. Press 

A

 to stop LCD test. You will then see a flashing 

KM/H

UNIT SELECTION (Fig 1.3)

Press 

A

 to toggle between 

KM/H

 or 

M/H

 (Mile/hour). Press 

B

 to confirm the current selection.

CIRCUMFERENCE DATA SETTING (Fig 1.4a)

1. The  display  shows 

  for  the  Bike 

1

  default 

circumference value of 2155mm. Measure the value for 
your wheel by following the steps below. (The Bike 

2

 

default circumference value is 2050mm.)

*

MEASURING WHEEL CIRCUMFERENCE (Fig 1.4b) 

Roll the wheel until the valve stem is at its lowest point 
(closest  to  the  ground)  then  mark  this  first  point  on 
the  ground.  Roll  the  bicycle  forward  until  the  wheel  has 
completed one full revolution and the valve stem returns 
to its lowest point. Mark the second point on the ground. 
Measure the distance between the marks. Enter this value 
to  set  the  wheel  circumference.  It  is  important  that  this 
measurement  is  accurate  to  ensure  correct  data  input  
when riding.

ODOMETER AND TOTAL TRIP TIME DATA SETTING (Fig 
1.5)

1. Designed  for  entering  in  previous  data  of 

ODO

 

1

ODO

 

2

*

T.TIMED TRIP

 

1

 and 

T.TIMED TRIP

 

2

*

 after a 

battery replacement. A new user does not need to set 
this data. Each press of 

B

 advances to the next data 

setting screen.

2. Adjust  the  digits  as  described  in  the  Data  Setting 

Process. 

(Fig 1.1)

MAIN UNIT SETUP 

Fig 1.1

DATA SETTING PROCESS

2 seconds

2 seconds

* = N.E.R.D Wireless 12 Function Cycle Computer only

Содержание NERD 12














Отзывы: