Knog NERD 12 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 13

Knog NERD 12 Скачать руководство пользователя страница 13

13

Sensor with transmitter

Non-contact magnet sensor with analogue wireless transmitter

Wireless sensing distance

55cm (1.8 feet) between the transmitter and the main unit.

Cross talk/interference

Within 40cm (15.8”), no interference by 2 bicycles carrying similar cycle
computers, even when ridden side by side.

Wheel circumference setting

1mm-3999mm (1mm increments)

Operating temperature

0°C - 50°C (32°F - 122°F)

Storage temperature

-10°C - 60°C (14°F - 140°F)

Main unit battery power

×1 CR2032 3V cell.

The transmitter battery should last approximately one year with an average

usage of around 1.5 hours per day.

Transmitter unit battery power

×1 LR44 1.5V cell.

The transmitter battery should last approximately one year with an average

usage of around 1.5 hours per day.

Dimensions

Main unit: 53 × 51 × 40mm
Transmitter unit: 52 × 27 × 52mm

Weight

Main unit: 45 grams
Transmitter unit: 39 grams

THE FULL N.E.R.D. SPECS:

* = N.E.R.D Wireless 12 Function Cycle Computer only

«
...
11
12
13

Содержание NERD 12














Отзывы:

Нет отзывов