Knight 106 Скачать руководство пользователя страница 37

Страница: 37 / 48

Troubleshooting

(continued)

Service Manual

Table 3-4 Troubleshooting Chart - Fault Messages Displayed on Boiler Interface

FAULT

DESCRIPTION

CORRECTIVE ACTION

Gas Pressure SW

(will require a manual

reset once the condition

has been corrected. Press

the RESET button on the
SMART SYSTEM

display

to reset.)

- Either the optional manual reset low gas
pressure switch or the optional manual reset
high gas pressure switch tripped.

• Reset the pressure switches.

• Measure the supply gas pressure to determine cause

of failure. Natural gas pressures should be between

4 - 14 inches w.c. and LP gas pressures
should be between 8 - 14 inches w.c.

• Refer to Section 7 - Gas Connections of the Knight
  Boiler Installation and Operation Manual for detailed
  information concerning the gas supply.

• Correct the supply gas pressure if necessary.

• Check for a loose or misplaced jumper if pressure
switches are not installed.

- The gas pressure switch contacts on the
Low Voltage Connection Board are open.

• Check for a loose or misplaced jumper on the Low
Voltage Connection Board.

• Check for the addition of a device wired across the
gas pressure switch terminals on the Low Voltage
Connection Board.

Flow Switch/

LWCO

(will require a manual

reset once condition has

been corrected. Press

the RESET button on the
SMART SYSTEM display

to reset.)

- Either the optional flow switch or the optional
low water cutoff is not making.

• Check boiler pump operation on a call for heat.

• Check for closed valves or obstructions in the boiler
piping.

• Verify system is full of water and all air has been
purged from the system.

• Check for loose or misplaced jumpers if flow switch or
LWCO is not installed.

- Blown fuse.

• Replace fuse F3 on the control board, see page 33
of this manual.

Blocked Drain SW

(will require a manual

reset once condition has

been corrected. Press

the RESET button on the
SMART SYSTEM display

to reset.)

The blocked drain switch has detected
excessive condensate build up inside the
unit.

• Check condensate tube from unit to floor drain for
proper installation and obstructions.

• Inspect condensate trap for blockage. Clean if
necessary.

• Check for loose wiring connection at wire harness
plug.

• Bad blocked drain switch. Replace switch.

Содержание 106

















































Результаты поиска

Содержание 106

Отзывы:

Похожие инструкции для 106

Бренды по названию

Популярные бренды

Knight 106, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 106

Отзывы:

Похожие инструкции для 106

Бренды по названию

Популярные бренды