Knick Protos II 4400 Скачать руководство пользователя

Страница: 67 / 112

Maintenance

Sensor monitor, temp probe adjustment

Note: Function check (HOLD) mode active

Menu Display

Maintenance

Open Maintenance

From the measuring mode:

Press menu key to select menu.

Select maintenance using arrow keys,

confirm by pressing enter.

Passcode as delivered: 2958

Then select "Module PH".

Temp probe adjustment

This function allows compensating

for the individual temperature probe

tolerance and the influence of the

lead resistances to increase the accu-

racy of temperature measurement.

Make sure that the process tempera-

ture is precisely measured using a

calibrated reference thermometer

when performing an adjustment! The

measurement error of the reference

thermometer should be less than

0.1 °C. Adjustment without precise

measurement might result in consid-

erable deviations of the measured

value display!

Sensor monitor

for validation of sensor and complete

measured-value processing.

Menu selection

Return to meas

22.3 °C

Select:

[enter]

Lingua

7.00 pH

Sensor monitor

Return

pH input

22.3 °C

ORP input

Adjust temp probe

Return

Probe tolerance and lead adjustment

22.3 °C

Enter measured process temp

22.3 °C

Installation adjustment

7.00 pH

RTD

Temperature

Impedance ref (25°C)

-56 mV

200 mV

1100 Ω

25 °C

086.5 kΩ

Process temp:

Off

1) With Protos II 4400(X) in the Calibration menu

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos II 4400

















































































































Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды

Knick Protos II 4400, Руководство пользователя

Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды