Knick Portavo 904 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 54

background image

15

Commissioning

Switching On the Meter

When you have connected the sensor, you can switch on the meter
by pressing the

meas

or

on/off

key.

If you press

meas

, the meter immediately switches to measuring

mode.

Analog sensors:

After pressing the

on/off

key, the meter displays selected adjust-

ment data before it switches to measuring mode.

Memosens sensors:

After pressing the

on/off

key, the meter displays selected sensor

information, incl. adjustment data, before it switches to measuring
mode.

Alternating Use of Analog and Memosens Sensors

The meter initially starts in analog measuring mode. If a Memosens sensor is con-
nected and detected during operation, the meter switches to Memosens.
If the Memosens sensor is now removed, the meter remains in Memosens mode. If
you want to resume measurements with an analog sensor, the meter needs to be
restarted by pressing the

on/off

key. The Memosens cable may remain connected.

Error message

Battery

charging level

Sensoface

Temperature

detector

Icons

Important information about the state of the device:

Process variable

Uncompensated measured value in MΩ cm

or

temperature compensation (TC)

Toggle by pressing

meas

.

Commissioning

Memosens sensor

Select menu items with arrow keys

«
...
13
14
15
16
17
...
»

Содержание Portavo 904























































Отзывы:

Нет отзывов

Похожие инструкции для Portavo 904

Бренд: Vanguard Instruments Страницы: 24

Бренд: Keithley Страницы: 32

Бренд: NanoEnTek Страницы: 4

Бренд: Olympus Страницы: 362

Бренд: Olympus Страницы: 8

Бренд: Teledyne Analytical Instruments Страницы: 107

Бренд: 3M Страницы: 168

Бренд: M&C Страницы: 18

Бренд: CONDTROL Страницы: 27

Бренд: Tegam Страницы: 36

Бренд: ICP DAS USA Страницы: 71

Бренд: CONDTROL Страницы: 11

Бренд: Milwaukee Страницы: 17

Бренд: Kabelmat Страницы: 27

Бренд: wtw Страницы: 63

CHEM2000-UV-VIS

Бренд: Ocean Optics Страницы: 42

Бренд: Oceanic Страницы: 64

Бренд: Bamo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды