Knick A405B Скачать руководство пользователя

Страница: 81 / 108

Error Messages

Error

Info text

(is displayed in case of fault when
the Info key is pressed)

Problem
Possible causes

ERR 99

DEVICE FAILURE

Error in factory settings

EEPROM or RAM defective
This error message only occurs in the
case of a total defect. The device must be
repaired and recalibrated at the factory.

ERR 98

CONFIGURATION ERROR

Error in configuration or
calibration data

Configuration or calibration data defec-
tive; completely reconfigure and recali-
brate the device.

ERR 95

SYSTEM ERROR

System error

Restart required.
If error still persists, send in the device
for repair.

ERR 01

NO SENSOR

Sensor error

Device type not assigned
Defective sensor
Sensor not connected
Break in sensor cable

ERR 02

WRONG SENSOR

Wrong sensor

ERR 04

SENSOR FAILURE

Failure in sensor

ERR 05

CAL DATA

Error in cal data

ERR 10

CONDUCTANCE TOO HIGH

Display range exceeded

Conductivity:
Conductance > 3500 mS

ERR 11

RANGE

Display range violation

ERR 13

TEMPERATURE RANGE

Temperature range violation

Содержание A405B













































































































Результаты поиска

Содержание A405B

Отзывы:

Похожие инструкции для A405B

Бренды по названию

Популярные бренды

Knick A405B, Руководство пользователя

Результаты поиска

Содержание A405B

Отзывы:

Похожие инструкции для A405B

Бренды по названию

Популярные бренды