KNF NF 1.100 EX Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 32

KNF NF 1.100 EX Скачать руководство пользователя страница 13

Diaphragm liquid pump NF 1.100 EX

Installation and connection

KNF Flodos AG BA_NF1.100EX_EN_05_152147
English translation of original Operating and Installation Instructions

13

6. Installation and connection

Only install pumps under the operating parameters and conditions
described in Chapter 4, Technical data, and in Section 2.3, Using
the pump in a potentially explosive atmosphere.

Observe the safety precautions (see Chapter 3).

6.1. Installation

➔

Before installation, store the pump at the installation location to

bring it up to ambient temperature.

➔

Mounting dimensions (see Fig. 3)

NF1.100 Ex

NF1.100.27 Ex

Fig. 3: Mounting dimensions NF1.100 Ex

➔

For pumps with fan: When installing the pump, make sure that

the motor’s fan can draw in an adequate amount of cooling air.

➔

Make sure that the installation location is dry and the pump is

protected against water in the form of rain, spray, splashes and
drips.

➔

Protect the pump against dust.

➔

Protect the pump against vibration and impact.

Mounting dimensions

Cooling air supply

Installation location

«
...
11
12
13
14
15
...
»

Содержание NF 1.100 EX

































Отзывы:

Нет отзывов