KNECHT S 200 BS Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 46

KNECHT S 200 BS Скачать руководство пользователя страница 13

14

Remove power plug. Cordon off the repair area as far as it is required.

After completing maintenance work and rectifying any faults, install all safety devices
and verify that they are fully functional.

2.4.10 Structural alterations to the grinding machine

Alterations to or retrofits or rebuilds of the grinding machine are not allowed without the permis-
sion of the manufacturer. This also applies for installation and configuration of the safety devices.

Any conversion work requires the written permission from KNECHT Maschinenbau GmbH.

Immediately replace any machine parts that are not in a serviceable state.

Use only original replacement and wear parts. When using external parts, it cannot be guaranteed
that they are constructed and manufactured to be suitable and safe.

2.4.11 Cleaning the grinding machine

Properly handle any cleaning agents and materials used and dispose of them in an environmental-
ly-friendly manner.

Dispose of the wear parts and replacement parts in a safe and environmentally-friendly manner.

2.4.12 Lubricants / oils and greases

When using oils and greases, follow the safety regulations applicable to the product. Comply with
the special regulations for the foodstuffs sector.

2.4.13 Relocation of the grinding machine

Disconnect the grinding machine from any external current supply, even if adjusting its position
slightly. Before restarting the grinding machine, properly connect it to the power supply.

When loading or unloading, only use suspension devices and load suspension devices with
sufficient load-bearing capacity. Designate suitable lifting devices for the lifting process.

Ensure that only persons authorized to carry out this work are located where the machine is
unloaded and installed.

Only lift the grinding machine correctly with a suspension device in accordance with the operating
instructions. Use only a suitable transport vehicle with sufficient carrying capacity. Secure loads
safely. Use suitable attachment points. When recommissioning, do so only in accordance with the
operating instructions.

2. Safety

«
...
11
12
13
14
15
...
»

Содержание S 200 BS















































Отзывы:

Нет отзывов