Step 1
If cabinet door is attached to cabinet,
remove hinges from cabinet frame
and door, and set door aside for use
in Step 6.
Mark front location for attaching
slides. On face frame cabinetry, mark
14-3/4˝ up from the top edge of
bottom frame cross rail on both front
frame stiles. Mark on interior edge of
frame stile. This line will indicate the
slide centerline. Using a level, verify
that both marks on cabinet frame are
level. To properly locate the cabinet
member of the slide front to back and
allow for a 2mm setback, a second
mark should then be placed 1/2˝ back
from the front of the face frame. This
mark, 1/2˝ back from the front edge
indicates the location of the front
mounting screws for left and right
slides. (figure A)
Optional step
Using 1/16˝ drill bit, drill pilot holes for inserting screws.
Mark rear location for attaching slides. On face frame cabinetry, measure 14-
3/4˝ up from the cabinet bottom on the cabinet back panel. If you have a
recessed cabinet bottom that sits below the top of the bottom face frame rail,
you will need to add the amount of face frame reveal to this number. Mark this
location. (Example: cabinet bottom is 1/4˝ below the top edge of face frame =
14-3/4˝ + 1/4˝ equals 15˝ high mark). Using a level, verify that both marks on
cabinet back panel are level.
Step 2
On the 14-3/4˝ height line determine the centerline of the back panel and
measure out from the centerline on either side 5-1/16˝ for the PDMTM12-1-35;
or 7-9/16˝ for the PDMTM15-2-35. These marks will indicate where the inside
edge of each slide mounting bracket will sit. Align the rear slide mounting
bracket to this mark, with the bracket centered on the 14-3/4˝ vertical height
line. Using two (2) #7 x 1/2˝ panhead sheet metal screws, attach bracket to
cabinet back panel. Repeat this process for attaching other rear-mounting
bracket.
Optional step
Using 1/16˝ drill bit, drill pilot holes for inserting screws.
TOP-MOUNT WASTE AND
RECYCLING UNIT
Installation Instructions
KNAPE & VOGT MANUFACTURING COMPANY
P.O. Box 191, Muncie, IN 47308
0.899.6535 • 765.288.8730 • Fax 765.288.0851 • www.kv.com
RN-249E 04/03
Note: This product is designed specifically for use with traditional 1-1/2˝ wide face frame
style cabinetry. To use with non-traditional face frame cabinetry, or Euro-style frameless
cabinetry, additional blocking may be required to provide the correct cabinet opening width.
Inspect all parts and read all instructions prior to beginning assembly and installation.
Parts Included
A. One (1) sliding bin assembly (Slide brackets,
sliding members and platform pre-
assembled)
B. 35 qt. white bin(s) (one with PDMTM12-1-35)
C. One (1) white wire accessory basket (only
on PDMTM12-1-35 models)
D. Two (2) Rear Slide Mounting Brackets
E. Four (4) Door Brackets (two are 1-1/4˝ wide
and two are 2-1/4˝ wide)
F. Four (4) #6-18 x 5/8˝ Phillips flathead sheet
metal screws for mounting door brackets
G. Four (4) #10-24 x 1/4˝ Phillips pan head
machine screws
H. Eight (8) #7 x 1/2˝ Phillips pan head sheet
metal screw for mounting slide members
Tools Required
•
Phillips head
screwdriver
•
Drill with 1/16” (1.5mm) bit for drilling pilot
holes
•
Tape measure or ruler
•
Pencil
•
Level
Product Assemblies
PDMTM12-1-35
PDMTM15-2-35
Disconnect Lever
Single Bin
Platform and Basket
Double Bin Platform
7-9/16˝
(FOR DOUBLE BIN)
5-1/16˝
(FOR SINGLE BIN)
FIGURE A
