background image

MEP-4xxx Direct-Coupled Actuators (40 to 90 in-lb.) 

10 

Applications Guide, AN0513A Rev. J

 WARNING

Risk of electrical shock in line-voltage models. 
Disconnect ALL power before servicing. More 
than one disconnect provided on models 
with auxiliary switches. Failure to follow 
electrical safety precautions with live electrical 
components could result in injury or death.

 WARNING

If both conduit connections are used in line-
voltage models, they MUST be externally 
connected during installation. The nonmetallic 
enclosure does not provide grounding 
connection between the two conduit 
connections.

Wiring Issues

• 

Check for correct wiring for the application.

• 

Check the wiring at the connected devices.

•  Use a voltmeter and ohmmeter to check the 

terminals for expected values.

•  See 

Tips for Connecting 24-Volt Power Applica

-

tion Note (AN0604D)

.

NOTE:  Wiring must be adequate to avoid exces

-

sive voltage drop on long runs! Allow 

plenty of “cushion” in measurements. A 

meter may be too slow to register tran-

sient dips or peaks during startup.

Configuration

Proportional (MEP-4xx2) Models Setup

NOTE: 

Before Jan. 2014, 

MEP-40x2/48x2 

proportional 

models had 

0–10 VDC inputs

 

and 

0–5 or 0–10 VDC feedback

 (only).

 

From 2014 through July 2015, they had 

2–10

 VDC inputs and 

1–5 or 2–10

 VDC 

(only) feedback instead. Starting in August 

2015, 

all

 these options were available and 

selectable via a jumper and slide switch.

NOTE: 

Before August 2015, the 

MEP-

42xx/45xx/49xx fail-safe

 proportional 

models had 

2–10

 VDC inputs and 

1–5 or 

2–10

 VDC feedback (only). Starting in 

August 2015, 

0–10

 VDC inputs and 

0–5 or 

0–10

 VDC feedback were also available and 

switch-selectable.

NOTE: 

When the 

0

–10 VDC input is selected, 

selectable feedback options are 

0

–5 or 

0

–10 

VDC. When the 

2

–10 VDC input is selected, 

feedback options are 

1

–5 or 

2

–10 VDC.

For instructions in direction, 

feedback, and 

au-

tomapping, see the relevant installation guide:

• 

MEP-4000/4800 Series (40/80 in-lb.) Installation 

Guide

• 

MEP-4200/4500/4900 Series (fail-safe, 25/45/90 

in-lb.) Installation Guide

Содержание MEP-4 Series















Отзывы: