background image

2

1

NOTE: 

The 

V-clamp nuts

 

3

 should be on top.

3

2.  Turn the controller over.

3.  Remove the 

stop screw

 

4

 from the storage 

location and clean any debris from the 

threads.

4

4.  Insert the stop screw into the 

60

 

5

 or 

45

 

6

 

stop hole position.

BAC-9000 Series VAV Controller

Installation Guide

INTRODUCTION

Complete the following steps to install a KMC 

Conquest™ BAC-9000 Series VAV Controller-

Actuator. For controller specifications, see the 

data sheet

 at 

kmccontrols.com

. For additional 

information, see the 

KMC Conquest Controller 

Application Guide

.

SET DRIVE HUB (45/60°) ROTATION LIMIT

NOTE: 

Complete the steps in this section 

if

 

the VAV damper rotation limit is either 

60 or 45

 degrees.

NOTE: 

If the VAV damper rotates 

90

 degrees, 

skip this section and go to 

Mount 

Controller on page 2 

instead.

1.  Push and hold the 

gear release

 

1

 and rotate 

the 

drive hub 

and

 V-clamp

 

2

 to the left.

KMC Controls, 19476 Industrial Drive, New Paris, IN 46553  

/

  877.444.5622  

/

  Fax: 574.831.5252  

/

  

www.kmccontrols.com

CONTENTS

Introduction .............................................. 1
Set Drive Hub (45/60°) Rotation Limit ............ 1
Mount Controller ........................................ 2
Connect Sensors and Equipment .................. 3
Connect (Optional) Pressure Sensor.............. 4
Connect (Opt.) Ethernet Network .................. 4
Connect (Optional) MS/TP Network............... 5
Connect Power .......................................... 5
Power and Communication Status ................. 6
MS/TP Network Isolation Bulbs .................... 6
Watch Dog Jumper ..................................... 7
Configure/Program the Controller ................. 7
Sample (BAC-9001) Wiring .......................... 8
Replacement Parts ..................................... 9
Important Notices ...................................... 9

Содержание BAC-9001










Отзывы: