klover ECOMPACT 150, Установка, использование, техническое обслуживание и полезные советы

Страница: 44 / 56

38
PELLET-BURNING BOILER ECOMPACT 150-190-250-290 EN -
Rev 1.1
PCB PARAMETERS
The parameters stored on the PCB are essential for the correct operation.
The following parameters are already stored during the testing of the appliance directly in the factory; these parameters
are the result of special tests using several types of pellets and must not be changed without the authorisation of Klover
srl so as not to impair the operation of the appliance.
The company shall not be held liable for any damage caused by the incorrect entry of parameters.
Parameter tables ECOMPACT 150
Parameters “VARIOUS CALIBRATIONS” - Mod. ECO150 (i05_220318)
Parameter Menu level Description Display Measurement Value field
Database
M0
Pr38 M08 – 4 – 01 Re-ignition block RE-IGNIT BLOCK Minutes 0 – 10 6
Pr39 M08 – 4 – 02 Flue gas extractor switch-off time MIN-EXT OFF Minutes 0 – 20 10
Pr40 M08 – 4 – 03 Pre-loading time in ignition IGNIT- PRE-LOAD Seconds 0 – 255 240
Pr41 M08 – 4 – 04 Stand-by time after pre-loading AFTER-PRE STAND-BY Seconds 0 – 255 180
Pr42 M08 – 4 – 05 Extractor speed in pre-loading phase
FLUE GAS-EXT
PRELOAD
RPM 350 – 2800 2200
Pr43 M08 – 4 – 06 ON/OFF temperature hysteresis on “SET H2O” DELTA ON OFF AUTO °C
0.0 – 20.0 5.0
Pr44 M08 – 4 – 07
Delay at economy operation mode switch-off (timer after reaching “SET
H2O” )
DELAY-OFF AUTO Minutes
2 – 120 20
Pr45 M08 – 4 – 08 Power change delay POWER CHANGE Seconds
0 – 60 20
Pr46 M08 – 4 – 09 ON/OFF Temperature hysteresis on “SET ROOM” DELTA ON AUTO °C
0.0 – 15.0 2.0
Pr47 M08 – 4 – 10 Keypad lock enable KEY LOCK-EN On – off On – off Off
Pr48 M08 – 4 – 11 Time after which an alarm is triggered in the event of a blackout BLACKOUT ALARM Seconds 0 – 60 30
Pr49 M08 – 4 – 12 Pellet level sensor enable PELLET RESERVE On – off On – off On
Pr50 M08 – 4 – 13 Pump start threshold and power modulation for overheating safety PUMP SAFETY °C 60 – 90 80
Pr51 M08 – 4 – 14
3-way switching and re-ignition delta on “SET BOILER” and “SET
BUFFER ”
DELTA PUF-BOI °C 0 – 15 5
Pr52 M08 – 4 – 15 Preheating time PREHEATING TIME Seconds 0 – 480 0
Pr53 M08 – 4 – 16 Extractor speed in preheating phase
PREHEAT-F.GAS-
SPEED
RPM 500 – 2800 2800
Pr54 M08 – 4 – 17
Time after which the “NO PELLET” alarm is triggered if “PELLET
RESERVE”
RESERVE ALARM Minutes 1 – 180 40
Pr55 M08 – 4 – 18 ON time for turbulator cleaning gear motor TURBOLAT DURATION Seconds 0 – 600” 120
Pr56 M08 – 4 – 19 ON time for brazier cleaning gear motor (NOT USED) CLEANING TIME Seconds 0 – 120” 0
Pr57 M08 – 4 – 20
Time from switching OFF after which the brazier cleaning takes place
(NOT USED)
CLEANER DELAY Minutes 1 – 15’ 1
Pr58 M08 – 4 – 21
Time from switching ON after which the brazier cleaning takes place (NOT
USED)
CLEANER STAND-BY Hours 1 – 24 24
Pr59 M08 – 4 – 22
Pump activation threshold and switching 3-way valve in DHW OUTPUT
MODE (with Type 2 System)
PUMP THRESHOLD I2 °C 55 – 75 60
Parameters “VACUUM CALIBRATIONS” - Mod. ECO150 (i05_220318)
Parameter Menu level Description Display Measurement Value field
Database
M0
Pr133 M08 – A – 01 Enable automatic pellet loading vacuum ENABLE VACUUM On – off On – Off Off
Pr134 M08 – A – 02 Vacuum on time VACUUM ACTIVE Seconds 1 – 180 20
Pr135 M08 – A – 03 Vacuum rest time VACUUM PAUSE Seconds 5 – 60 10
Pr136 M08 – A – 04 Number of operating cycles VACUUM CYCLES Number 1 – 20 15
Pr137 M08 – A – 05 Enables a Vacuum operating test to be performed VACUUM TEST On – off On – off Off
Parameters “FACTORY CALIBRATIONS” - Mod. ECO150 (i05_220318)
Parameter Menu level Description Display Measurement Value field
Database
M0
Pr01 M08 – 6 – 01 Ignition cycle maximum time IGNIT- MINUTES Minutes 5 – 25 18
Pr02 M08 – 6 – 02 Start time START MINUTES Minutes 2 – 12 8