KlimaTeknik KT10X Скачать руководство пользователя страница 14

Страница: 14 / 16

If you suspect something is wrong with your Heat Pump?

Before you call for service, fill out below. (Reg. Card

is sent to

NICO Norge __)

Send to your Dealer and keep a copy in front of you when you call.

Model written on Heat Pump: ___________________ Serial No:______________

Delivered from Company: ______________________________________________

Installation date: ________ Installed: Outside __ Inside__ inside in a shed __

Distance to obstacles: Front ___ m

Back ____ m

Top ____ m

Pool Surface Area ________ m2

Pool is: Covered __

Uncovered __

Other Heating system for the Pool: Yes __ No __ Desired Pool temp ____C

Normal Air Temperature: ______C

Normaly: Dry Air __ Humid Air __

Pool Filter Pump: ________ kW. Filter is Clean __ Pressure on filter: ____

Max Pool Temperature reached_____ C°

Desired Pool Temp _____C°.

Is there Ground Water around the pool? YES__ NO__ DON’T KNOW__

Any Failure Code on Display _____. Check Settings. See Default Settings:

Observed Settings: ____________________________________________

Is the heat pump: Running __ Running sometimes __ Not running at all ___

Is the heat pump: Heating __ Not Heating enough __ Not heating at all __

Is the fan running? YES__ NO__ Is there ice on “Radiator” YES__ NO__

Is there Cold Air coming out from Radiator: YES__ NO__ DON’T KNOW__

Are there leaves or dirt on the fins on the “Radiator” YES__ NO__

Gas Pressure on heat pump? Running _____Pa Not running _____ Pa

Do Following:

Switch Main Power OFF. Wait 3 min. Power ON, Heat Pump ON. > Listen:

Does the

fan

start within 2 Min? YES__ NO__

Does the

compressor

start within next 2 Min? YES__ NO

Check:

Voltage on Heat Pump connections: Standby __V. ON__V. Running __V

Fuse for Heat Pump _______A Cable size from Fuse to Heat Pump _____mm2

Are the Fuse if Type: Slow Blow / Motor Fuse / Yes___ No___

Parameter Settings

If Possible read, and Note all parameter settings. (See Page 6)

0 = _____

1 = _____

2 = _____

3 = _____

4 = _____

5 = _____

6 = _____

7 = _____

8 = _____

9 = _____

A = _____

B = _____

C = _____ D = _____

E = _____

F = _____

NOTES___________________________________________________________

Содержание KT10X

















Результаты поиска

Содержание KT10X

Отзывы:

Похожие инструкции для KT10X

Бренды по названию

Популярные бренды

KlimaTeknik KT10X, Руководство пользователя

Результаты поиска

Содержание KT10X

Отзывы:

Похожие инструкции для KT10X

Бренды по названию

Популярные бренды