20
SYNTH TABLES
Roland Juno-1 Juno-2 and HS-10
Cable requirements
The Roland Juno-1/HS-10 uses a standard MIDI cable
Equivalent controls
Roland
©
Juno-1/HS-10 Controls Pg1
Osc 1 Range (1)
32',16', 8', 4'
LFO Wave (26)
Not Used (sine only)
Osc 1 Wave (2)
Sawtooth Waveform Select
LFO Delay (27)
Active
Osc 1 PW (3)
DCO PW/PWM
LFO Speed (28)
Active
Osc 1 Tune (4)
Not Used
Chorus/FX Rate (29)
Active (Chorus Rate)
Osc 1 LFO Mod (5)
Active
Chorus/FX Mode (30)
Chorus On, Chorus Off
Osc 1 ENV Mod (6)
Active
HPF (31)
Active
Osc 1 Mode (7)
PW Waveform Select
LPF Cutoff (32)
Active
Osc 1 PWM (8)
PWM Rate
LPF Resonance (33)
Active
Osc 1 Level (9)
Not Used
Filter LFO Modulation
(34)
Active
Noise Level (10)
Active (0-3 range)
Filter ENV Modulation
(35)
Active
Osc 2 Range (15)
Not Used
Filter Key Follow (36)
Active
Osc 2 Wave (16)
Sub Osc Waveform & Octave Select
Filter ADSR (37-40)
Not Used
Osc 2 PW (17)
DCO Aftertouch Depth
Filter Mode (41)
Active EG Mode
Osc 2 Tune (18)
Not Used
VCA ADSR (42-45)
Active 4 stage
Osc 2 Fine Tune (19)
Not Used
VCA Mode (46)
Envelope, Gate
Osc 2 LFO Mod (20)
VCF Aftertouch
VCA Level (47)
Active
Osc 2 ENV Mod (21)
VCA Aftertouch
Osc 2 Mode (22)
Used to select Env type for Osc ENV Mod
Osc 2 PWM (23)
Envelope Key Follow
Osc 2 XMod (24)
Not Used
Osc 2 Level (25)
Sub Osc Level (0-3 Range)
Roland
©
Juno-1/HS-10 Controls Pg2
Osc 1 Range (1)
Not Used
LFO Wave (26)
Not Used
Osc 1 Wave (2)
Not Used
LFO Delay (27)
Not Used
Osc 1 PW (3)
Not Used
LFO Speed (28)
Not Used
Osc 1 Tune (4)
Not Used
Chorus/FX Rate (29)
Not Used
Osc 1 LFO Mod (5)
Not Used
Chorus/FX Mode (30)
Not Used
Osc 1 ENV Mod (6)
Not Used
HPF (31)
Not Used
Osc 1 Mode (7)
Not Used
LPF Cutoff (32)
Active
Osc 1 PWM (8)
Not Used
LPF Resonance (33)
Active
Osc 1 Level (9)
Not Used
Filter LFO Modulation
(34)
Active
Noise Level (10)
Not Used
Filter ENV Modulation
(35)
Active
Osc 2 Range (15)
Not Used
Filter Key Follow (36)
Active
Osc 2 Wave (16)
Not Used
Filter Decay
T1 Time
Osc 2 PW (17)
Not Used
Filter Sustain
L1 Level
Osc 2 Tune (18)
Not Used
Filter Release
T2 Time
Osc 2 Fine Tune (19)
Not Used
Filter Mode
Not Used
Osc 2 LFO Mod (20)
Not Used
VCA Attack
L2 Level
Osc 2 ENV Mod (21)
Not Used
VCA Decay
T3 Time
Osc 2 Mode (22)
Not Used
VCA Sustain
L3 Level
Osc 2 PWM (23)
Not Used
VCA Release
T4 Time
Osc 2 XMod (24)
Not Used
VCA Mode (46)
Not Used
Osc 2 Level (25)
Not Used
VCA Level (47)
Not Used
Roland Juno 1, Juno 2 & HS-10 Notes
The Juno 1, Juno 2 & HS-10 synthesizers have one oscillator and a sub oscillator for each of the six voices. The oscillator
design is a digital system and the filter and the VCA is the custom Roland chip the IR3R05 for each of the six voices. The HS-
10 is the same as the Juno-1 apart from the panel sticker on the front.
The oscillator 1 Wave switch (1) is used to step though all possible Sawtooth wave types. These are Off, Sawtooth type 1,
Sawtooth type 2, Sawtooth type 3+PW, Sawtooth type 4 and Sawtooth type 5. For the Sawtooth type 3+PW waveform the
PW level control (3) is used to adjust the PW and the PWM Speed control (8) is used to give a PWM LFO effect. Fully off on
the PWM Speed (8) stops the LFO and PW control is manual only using the PW control (3). These controls will have no effect
for the other Sawtooth wave types.
The oscillator 1 Mode switch is used to step through all the possible pulse wave types. Valid types are Off, Pulse type 1,
Pulse type 2 and Pulse type 3+PW. For the Pulse type 3+PW waveform the PW level control is used to adjust the PW and the
PWM Speed control is used to give a PWM LFO effect. Fully off on the PWM Speed stops the LFO and PW control is manual
only using the PW control. These controls will have no effect for the other Pulse wave types.
Oscillator 2 on the Patch Editor is used to control the sub oscillator. The oscillator 2 wave switch (16) is used to step through
all the possible sub oscillator wave forms and octaves. These are -1 octave Square Wave, minus one octave Pulse wave type
1, 2 and 3, minus 2 octaves Square wave and minus 2 octaves pulse wave. This and the level control (25) are the only valid
controls for the sub oscillator.
Oscillator 2 Mode Button (22) is used to select the envelope mode for the Osc ENV mod (6). Valid options are Normal,
Inverted, Normal with Dynamics, Inverted with Dynamics. The Filter Mode Button (41) has the same options for the Filter ENV
control (35).
There is no separate EG controls for the filter and the VCA EG controls (42-45) are used for Oscillator, Filter and VCA
modulation. The VCA Mode Button (46) has 4 valid options. Envelope, Gate, Envelope with Dynamics and Gate with
Dynamics
www.kiwitechnics.com
Patch Editor v6.0
Содержание Patch Editor
Страница 1: ...Patch Editor...
