background image

10

For Roof Venting Installation Only

1. Insert damper assembly through the cabinet cutout so that the 

long tab of the damper assembly slides into the slot on the left 
side of the damper vent opening, as shown. Then secure with 
mounting screw.

NOTE: The screw cannot be installed if the damper assembly is 
not positioned as shown.

2. Connect vent to damper assembly.

Install Filters

The grease and charcoal filters must be installed in the bottom of 
the microwave hood combination. See the User Instructions for 
care and replacement information.

To Install Filters:

1. Make sure filters are stacked in the filter frame as shown 

above.

2. Install the filters by inserting the wide tab of the filter frame 

into the inner portion of the filter housing, then swinging the 
outside of the frame up until it fits into place.

Complete Installation

1. Plug microwave oven into grounded 3 prong outlet.
2. Reconnect power.
3. Check the operation of microwave oven by placing 1 cup 

(250 mL) of water on the turntable, and programming a cook 
time of 1 minute at 100% power. Test vent fan and exhaust by 
operating the vent fan.

4. If the microwave oven does not operate:

Check that a household fuse has not blown, or that a 
circuit breaker has not tripped. Replace the fuse or reset 
the circuit breaker. If the problem continues, call an 
electrician.

Check that the power supply cord is plugged into a 
grounded 3 prong outlet.

See the User Instructions for troubleshooting information.

Installation is now complete.
Save Installation Instructions for future use.

A. Long tab (inside slot)
B. Damper assembly

C. Mounting screw
D. Upper cabinet cutout

A. Vent
B. Damper assembly (under vent)

A. Retaining spring
B. Filter frame

C. Grease filter (metal)
D. Charcoal filter (black)

A                             B                                  C

D

A              B

A    B      C     D

A. Filter frame
B. Wide tab

C. Microwave oven bottom

A    B       C

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, 
fire, or electrical shock.

WARNING

Содержание KHMS2056SSS - ARCHITECT II 36" 2.0 cu. Ft. 1













Отзывы: