background image

7

Mark Rear Wall

The microwave oven must be installed on a minimum of 1 wall 
stud, preferably 2, using a minimum of 1 lag screw, preferably 2.

1.

Using measuring tape, find and clearly mark the vertical 
centerline of the opening.

A. Centerline

2.

With the support tabs facing forward (see illustrations in 
“Possible Wall Stud Configurations” in “Locate Wall Stud(s)” 
section), align the mounting plate center markers to the 
centerline on the wall, making sure it is level, and that the top 
of the mounting plate is butted up against the bottom edge of 
the upper cabinet.

NOTE:

 If the front edge of the upper cabinet is lower than the 

back edge, lower the mounting plate so that its top is level with 
the front edge of the cabinet.

3.

Holding the mounting plate in place, mark both bottom corner 
holes.

4.

Find the wall stud centerline(s) marked in Step 2 of “Locate 
Wall Stud(s),” and mark at least 1, preferably 2, hole(s) through 
the mounting plate, closest to the centerline(s). See figures 1, 
2 and/or 3 in “Possible Wall Stud Configurations” in “Locate 
Wall Stud(s)” section. The blackened holes in the shaded 
areas are ideal hole locations.

5.

Set mounting plate aside.

Wall Venting Installation Only

6.

Mark the centerline 3/8" (1 cm) down from the bottom edge of 
the upper cabinet.

7.

Using measuring tape, measure out 6" (15.2 cm) on both sides 
of the centerline, and mark.

8.

Measure down 4" (10.2 cm) from the mark made in Step 6, 
and mark.

9.

Using a straightedge, draw the 2 horizontal, level lines through 
the marks made in steps 6 and 8.

10.

Draw the 2 vertical, plumb lines down from the marks made in 
Step 7 to complete the 12" x 4" (30.5 x 10.2 cm) rectangle. 
This is the venting cutout area.

11.

Cut a 3/4" (19 mm) hole in one corner of the cutout area.

12.

Using a keyhole saw, cut out the venting cutout area.

Drill Holes in Rear Wall

In addition to being installed on at least 1 wall stud, the mounting 
plate must attach to the wall at both bottom corner holes. If the 
holes are not over wall studs, use two 1/4-20 x 3" round-head 
bolts with toggle nuts; if 1 hole is over a wall stud, use 1 lag screw 
and one 1/4-20 x 3" round-head bolt with toggle nut; or if both 
holes are over wall studs, use 2 lag screws. Following are 
3 installation configurations.

Installation for No Wall Studs at Corner Holes 
(Figures 1 & 2)

1.

Drill 3/4" (19 mm) holes through the wall at both bottom corner 
holes marked in Step 3 of “Mark Rear Wall.”

2.

Drill 3/16" (5 mm) hole(s) into the wall stud(s) at the hole(s) 
marked in Step 4 of “Mark Rear Wall.” Refer to figures 1 and 2 
in “Possible Wall Stud Configurations” in “Locate Wall Stud(s)” 
section.

Installation for Wall Stud at One Corner Hole (Figure 3)

1.

Drill a 3/16" (5 mm) hole into the wall stud at the corner hole 
marked in Step 3 of “Mark Rear Wall.”

2.

If installing on a second wall stud, drill a 3/16" (5 mm) hole into 
the wall stud at the other hole marked in Step 4 of “Mark Rear 
Wall.” Refer to Figure 3 in “Possible Wall Stud Configurations” 
in “Locate Wall Stud(s)” section.

3.

Drill a 3/4" (19 mm) hole through the wall at the other corner 
hole.

Installation for Wall Studs at Both Corner Holes (Figure 4)

1.

Drill 3/16" (5 mm) holes into the studs at the corner holes 
marked in Step 3 of “Mark Rear Wall.”

A. Rear wall
B. Mounting plate

C. Top of mounting plate must align 

with front edge of cabinet.

D. Front edge of upper cabinet

A

A

B

C

D

6" (15.2 cm)

6" (15.2 cm)

³⁄₈

" (1 cm)

Upper cabinet bottom

Centerline

4" (10.2 cm)

Содержание KHMS2050SSS - 30" Microwave Hood Combo













Отзывы: